Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

Lava Micro FlexDrive Driver (lavadrive2) fits pens

Status
Not open for further replies.





Morgan said:
Consider yourself corrected. :D

The Microboost was designed to run the higher power Blurays, (mainly 10x, 12x), as these started to require a higher output voltage than the 5.5V the Flexdrive could supply. Some of these BRs are going to the 7V area. Therefore the Microboost came about before the 445 diodes were even known about. The Flexdrive is fine for any 445nm diode as the forward voltage even at high power is only around 4.2V. The only limit is the current! At present we don't have a, "Just For 445nm", driver. I'm a looking forward to when we have one though!!!!

M
:)
Click to expand...

Morgan,

Can microboost be used for low powered diodes? Reds and PHRs? Will it not fry the LPC-815 with its low forward voltage requirement?

Thanks!
 
gillza said:
Morgan,

Can microboost be used for low powered diodes? Reds and PHRs? Will it not fry the LPC-815 with its low forward voltage requirement?

Thanks!
Click to expand...

No, you need a groove or a rckstr. If you want to drive a red with a single rechargeable, the flexdrive is the only option that I know of.
 
gillza said:
Morgan,

Can microboost be used for low powered diodes? Reds and PHRs? Will it not fry the LPC-815 with its low forward voltage requirement?

Thanks!
Click to expand...

Unfortunately you cannot use the microboost. Not because of the voltage. It would boost a 1.5V Battery to run a diode that is say around 3V. But the red uses a common ground negative pin and the microboost needs to have an isolated negative feed from the battery into the driver negative input. Since the negative pin on the diode is also a case pin meaning that it is in contact with the negative of the battery through the host. If you isolated your heatsink from the host it might work but that would be a pain on most hosts. Here is a link where Jay explains it a little better than me. http://laserpointerforums.com/f55/r...-taking-payments-now-48664-21.html#post781362
 
Last edited:
DTR said:
Unfortunately you cannot use the microboost. Not because of the voltage. It would boost a 1.5V Battery to run a diode that is say around 3V. But the red uses a common ground negative pin and the microboost needs to have an isolated negative feed from the battery into the driver negative input. Since the negative pin on the diode is also a case pin meaning that it is in contact with the negative of the battery through the host. If you isolated your heatsink from the host it might work but that would be a pain on most hosts. Here is a link where Jay explains it a little better than me. http://laserpointerforums.com/f55/r...-taking-payments-now-48664-21.html#post781362
Click to expand...


Thank you! Your explanation was perfectly understandable. The solution that Jayrob suggested for 445nm diode will not apply for LPC-815 since the case of LPC-815 IS the negative terminal in the diode and the bottom pin that is used as negative on most other diodes including the the 445 and 405 is just "hanging" there on the red diodes.... right? :)

For testing purposes few days ago I hooked the Microboost to LPC-815 directly in a lab-build manner. It worked fine. I just started to question whether it is safe to use a boost drive on low powered diodes after reading the comments. In layman terms Microboost will provide the voltage the diode requires. It will also boost from lower voltage input to higher output if need be.
 
Last edited:
It is hard time to wait for v6...

Hi. Drlava. When will I see v5 or v6?
 
gillza said:
Thank you! Your explanation was perfectly understandable. The solution that Jayrob suggested for 445nm diode will not apply for LPC-815 since the case of LPC-815 IS the negative terminal in the diode and the bottom pin that is used as negative on most other diodes including the the 445 and 405 is just "hanging" there on the red diodes.... right? :)

For testing purposes few days ago I hooked the Microboost to LPC-815 directly in a lab-build manner. It worked fine. I just started to question whether it is safe to use a boost drive on low powered diodes after reading the comments. In layman terms Microboost will provide the voltage the diode requires. It will also boost from lower voltage input to higher output if need be.
Click to expand...


Sounds about right. The groove 2 is great for these LOC's. Have built a few with them. I like to take a 3XAAA holder and use one of my custom AAA dummy battery I made for my eBay pens with two other 10440's in series. It will give you 8.4V fully charged.

aaadummy3.jpg

aaadummy1.jpg





SHIN said:
It is hard time to wait for v6...

Hi. Drlava. When will I see v5 or v6?
Click to expand...

Don't worry Shin the V5 will be back soon.:shhh:
 
I read somewhere that the pre-orders were already receiving v5s. If you were not on the list, you might be SOL.
 
I would guess that he is making sure he has enough in stock that when he updates his site with them as available they don't sell out in 5 minutes.;)
 
Status
Not open for further replies.


Back
Top