Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

How to Register on LPF | LPF Donations

GB: 4$ heatsinks, 1.5$ aluminum modules AND more!

Anodizing is done,

7484085940_79c98ab17b_z.jpg


Blue red, gold & silver are looking shweet :)

I'll keep everyone updated with the progress :)
 
Last edited:





The blue & red is really nice actually :) I'm sure there will be lots of nice builds with all this stuff :)
 
very purdy Tony.
and the color coordination is a must,.

After all the only thing that seperates us from the great apes is our ability to color coordinate our acessories.

side notage:
super glue needs to be kept far away from lenses until very dry.

some times its easier to make the hole a tad bigger- emory cloth wrapped around the right size drill bit does that job effortlessly- just stop and check the fit.

PLUS take apart an antenna from a radio and in between each section you will find varing sizes of nicely formed curved copper pieces( there to keep the antenna from coming apart)
these make excellant shims and being copper are good heat transferers.< -- (is that even a word??)
They normally have a little grease on them so you make want to wipe that off and add some thermal paste.

hope this has been a helpful post.. if so be sure to support this forum any way you can.....len:thanks:
 
Last edited:
hakzaw1 said:
very purdy Tony.
and the color coordination is a must,.

After all the only thing that seperates us from the great apes is our ability to color coordinate our acessories.

side notage:
super glue needs to be kept far away from lenses until very dry.

some times its easier to make the hole a tad bigger- emory cloth wrapped around te right size drill bit does that job efortlessly- just stop and check the fit.

PLUS take apart an antenna from a radio and in between each section you will find varing sizes of nicely formed curved copper pieces( there to keep the antenna from coming apart)
these make excellant shims and being copper are good heat transferers.< -- (is that even a word??)
They normally have a little grease on them so you make want to wipe that off and add some thermal paste.

hope this has been a helpful post.. if so be sure to support this forum any way you can.....len
Click to expand...

Thanks for the input :) glad ya like them :)
 
Yep definately nice job on this! I could care less about the wait. The products I'm sure will speak for themselves and you just cant get anywhere close to this price on the open market.

Also I know that the sh-032 will fit a sh-034(new shorter 16340 host). I wanted to grab the new sh-036 as well but I ran into laser pocket! I think it will fit it as well going by the dimentions but I cant be sure.

Anyway's Thanks again Anthot.
 
Kizdawg said:
Yep definately nice job on this! I could care less about the wait. The products I'm sure will speak for themselves and you just cant get anywhere close to this price on the open market.

Also I know that the sh-032 will fit a sh-034(new shorter 16340 host). I wanted to grab the new sh-036 as well but I ran into laser pocket! I think it will fit it as well going by the dimentions but I cant be sure.

Anyway's Thanks again Anthot.
Click to expand...


:thanks: for your patience & appreciation :)
 
Any idea if the sh034 can fit a 18350? I'm gonna have to get one of those ;)
 
The auraura's 034's wont take the 18mm only the 16's

I thaught the same thing and I baught 2x 18350's on my last batery order but they are not going to be able to fit unless ya remake the barrel

Actualy now that I measure I doubt you could drill it out either it's 19.05mm on the outside of the skinny part of the batery barrel.


IMG_4133 by Kizdawg, on Flickr


IMG_4137 by Kizdawg, on Flickr

Geese those are dirty! I guess I have been using them as flashlights still the pollished stainless is a hard one to keep clean! It will remind you of how durty humans are...:shhh:
 
Last edited:
Everything done! :D
But..... The heatsinks need to be plated gold now :p

Anyway here's what 700 brass set screws look like :)
7491826622_d7574f16cb_z.jpg


Obviously 1 included per heatsink ;)
 
Are you going to put every setscrew on ?:eek:
You have a patience of a monk :D

Well we are going to see the sinks soon.
 
Machinist Joe said:
Why not just include them in the package and have us put them in? :crackup:
Click to expand...

If I get the FedEx package in before 12 then I'll put them in cuz ill have time but if it's like last time I got it at 5:30 & had to be at the post office at 6 I was rushing like crazy so hopefully it's early :)
 
You must log in or register to reply here.


Back
Top