Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers



FS: My new 635nm 900mW - diode two pins

thanhtung

Active member
Joined
Oct 18, 2014
Messages
368
Points
43
my mail : hoangtuech.hn@gmail.com
- my diode set at 1200mA very bright, when i use G2 len i see wide dot and beam as same as blue diode. it is not too wide as MItshu P71,73,7x and sharp.
i like it
- in the picture 2 dots laser , i take photo at about 300m







 
Last edited by a moderator:



diachi

Well-known member
Joined
Feb 22, 2008
Messages
9,734
Points
113
Re: My new 635nm 900mW - diode two pins

Those are some nice looking hosts you have there!
 

Alaskan

Well-known member
LPF Site Supporter
Joined
Jan 29, 2014
Messages
11,612
Points
113
Re: My new 635nm 900mW - diode two pins

This guys creations are supreme, both in design and workmanship:






OK, I raved on and on, but what can I say, I'm pleased with these....
 
Last edited:
  • Like
Reactions: GSS

paul1598419

Well-known member
Joined
Sep 20, 2013
Messages
15,819
Points
113
Re: My new 635nm 900mW - diode two pins

I was looking for the red beam shot that showed the divergence of this build. As you said, it isn't as bad as the Mits ML501P73. I see the blue beam shot and it is not great. The hosts are nice looking, though.
 

logsquared

Active member
Joined
Dec 9, 2011
Messages
188
Points
28
Re: My new 635nm 900mW - diode two pins

I was looking for the red beam shot that showed the divergence of this build. As you said, it isn't as bad as the Mits ML501P73. I see the blue beam shot and it is not great. The hosts are nice looking, though.
Look at the picture of the spots on the far away building. You can see the red next to the blue.
 

paul1598419

Well-known member
Joined
Sep 20, 2013
Messages
15,819
Points
113
Re: My new 635nm 900mW - diode two pins

Look at the picture of the spots on the far away building. You can see the red next to the blue.
Oh, there it is. That looks as wide as the blue, if not wider. I am all for a 635nm diode with better divergence than the Mitsubishi P73, but I have to see a comparison to believe it. Color me not convinced. :D
 

paul1598419

Well-known member
Joined
Sep 20, 2013
Messages
15,819
Points
113
:crackup: With all that Texas sun, I believe you could be red. At least in the summer, Len. BTW, :thanks:
 
Last edited:

thanhtung

Active member
Joined
Oct 18, 2014
Messages
368
Points
43
Re: My new 635nm 900mW - diode two pins

I was looking for the red beam shot that showed the divergence of this build. As you said, it isn't as bad as the Mits ML501P73. I see the blue beam shot and it is not great. The hosts are nice looking, though.
dear, i have up dot red and blue at the house range about 300m! and they are same!
 

paul1598419

Well-known member
Joined
Sep 20, 2013
Messages
15,819
Points
113
Re: My new 635nm 900mW - diode two pins

dear, i have up dot red and blue at the house range about 300m! and they are same!
What diode did you use for the blue laser build? Is it a NUBM44 or something else?
 

jors

Member
Joined
May 9, 2014
Messages
73
Points
18
and what collimator? dot will be about the same if 3elem on red (say p73) and G2 on blue. Is that the trick? Nice host btw
 

paul1598419

Well-known member
Joined
Sep 20, 2013
Messages
15,819
Points
113
I have gone back several times to try to get an accurate comparison between the red divergence and the blue divergence. The red still looks wider to me, but the PLTB450B diode has a better divergence spec than an M140. Again, good luck with your sale. :)
 

Alaskan

Well-known member
LPF Site Supporter
Joined
Jan 29, 2014
Messages
11,612
Points
113
Red looks about 2x wider and almost 2X thicker to me, I would expect worse unless a single mode red.
 




Top