Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

FS: Aurora C6 Kits!

Status
Not open for further replies.
Shipped about 10 this morning. Would of been more but the printer ran out of black ink last night.
Ink is replaced and i'm packaging more orders up.

I'm right around the date of your order so you should be expecting a paypal shipping notification. I'm keeping an eye out for the one from washington state that's for 1.8a so i can change it to 1.6........

Thanks Moh!! :D
I got the paypal notification this morning! :D
So Im a bit confused... just to clarify did you have a chance to change the driver to 1.6A or should I send it home to you to have it corrected? Because If its still at 1.8A ill gladly pay the postage fee both ways to have the units current corrected if needed :D

Again thanks for the update! :wave:
I know you work ALOT so no worries here
Take your time pal.

Take care and all the best to you :beer:
- Raj
 





Thanks Moh!! :D
I got the paypal notification this morning! :D
So Im a bit confused... just to clarify did you have a chance to change the driver to 1.6A or should I send it home to you to have it corrected? Because If its still at 1.8A ill gladly pay the postage fee both ways to have the units current corrected if needed :D

Again thanks for the update! :wave:
I know you work ALOT so no worries here
Take your time pal.

Take care and all the best to you :beer:
- Raj

I actually sent you a 1.8A kit. There is also a little baggie inside with a 3.3Ohm resistor.

If you remove the resistor labeled "2R2" from the driver and replace it with the "3R3" resistor located in the baggies, it will change it from 1.8A to 1.62A
 
Hey Moh,
I don't want to be a P.I.T.A. but I was wondering if you're shipping the kits ordered on black friday soon. I specifically ordered mine on the 26th; ETA on those shipments?

I'm only antsy because I've received my goggles, CR123a's, and diode/module and all I need now is a host for everything :D
 
I actually sent you a 1.8A kit. There is also a little baggie inside with a 3.3Ohm resistor.

If you remove the resistor labeled "2R2" from the driver and replace it with the "3R3" resistor located in the baggies, it will change it from 1.8A to 1.62A

Awesome!!! :D Thanks Moh!
 
Hey Moh,
I don't want to be a P.I.T.A. but I was wondering if you're shipping the kits ordered on black friday soon. I specifically ordered mine on the 26th; ETA on those shipments?

I'm only antsy because I've received my goggles, CR123a's, and diode/module and all I need now is a host for everything :D

Shep?

I was wanting to as you about yours. Your note says 1.5A
do you want 1.35 or 1.62A? that's the clostest ranges i have to 1.5A
 
I haven't received any e-mail from paypal about shipping yet... has mine gone out?
 
I got mine lastnight. Thanks Moh!

Just an FYI for others if they run into a problem like I did. I don't know if anyone else has run into this and shared their fix, but I thought I'd at least share what I did.

After a few hours of work, I went to fire my new 445 up and got nothing. It turns out the button on the c6 host wasn't working. I tried the common fix of tightening down the rings to make sure everything had good contact but that still didn't work. I just wasn't getting any power between the spring and the ring.

Ultimately I desoldered the button from the board and found that underneath it, there are 2 holes that go through the board and connect to the solder pad where the spring sits. On mine, they had not been filled with solder to complete the connection to the switch. I cleaned them out, added some solder and connected the two pads together. I put everything back together and now it works!

I didn't take time to take pictures, but if anyone has any questions, feel free to PM me and I can try to explain it a little bit better.
 
Hey there!
Thank you for sharing :) It may help those that would have otherwise been in the dark having no idea what to try next to get their lasers working again. :beer:

Clicky's have taken me through hell and back with the amount of problems ive had with them lol Now when something isnt right... check the clicky lol its always a simple fix though :D

I got mine lastnight. Thanks Moh!

Just an FYI for others if they run into a problem like I did. I don't know if anyone else has run into this and shared their fix, but I thought I'd at least share what I did.

After a few hours of work, I went to fire my new 445 up and got nothing. It turns out the button on the c6 host wasn't working. I tried the common fix of tightening down the rings to make sure everything had good contact but that still didn't work. I just wasn't getting any power between the spring and the ring.

Ultimately I desoldered the button from the board and found that underneath it, there are 2 holes that go through the board and connect to the solder pad where the spring sits. On mine, they had not been filled with solder to complete the connection to the switch. I cleaned them out, added some solder and connected the two pads together. I put everything back together and now it works!

I didn't take time to take pictures, but if anyone has any questions, feel free to PM me and I can try to explain it a little bit better.
 
There is only tracking for USA packages. international packages don't get shipped.
you should get a notification from paypal when they ship though.

Not sure what order is yours, but i should have all orders sent out and be completely caught up this weekend. I've got the last of the orders already assembled and the drivers arctic silvered to the pills. Now i'm just wiring them all up, after that i just have to test them and package them up.
 
I've added "Just add diode" kits back.
I've only added what i have finished that are ready to ship.

There are 1x 1.62A kits and 2x 1.8A kits. Once they are sold the rest will only be 1.25A kits.

Once I have ran through this batch of hosts, i won't be selling "just add diode" kits any more. They are just way too much time and work.
 
Ok, can those just be ordered? I PMed first because I don't know if any of them have been claimed.
 
Last edited:
Status
Not open for further replies.


Back
Top