Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

Anyone know an easy way to drill through washers?






Re: Anyone know an easy way to drill through washe

Don't washers already have a hole? What kind of drilling do you want done?
 
Re: Anyone know an easy way to drill through washe

Use a high powered laser, I hear they are wonderful ;D ;D ;D ;D ;D ;D ;D ;D ;D ;D Sorry, couldn't resist. How about a drill press & titanium bits ? phoenix77/rob 8-)
 
Re: Anyone know an easy way to drill through washe

i use a vise with grooves and put the washer in and drill with my drill on slow and dont put much pressure on it so it doesn't bend.

just go slow and be careful

drill press would be best though
 
Re: Anyone know an easy way to drill through washe

Drill and bit? I like step bits.

Drill press would be even better.
 
Re: Anyone know an easy way to drill through washe

I echo the step drill as it helps to prevent the judder that you will get using a standard drill.....

I personally would use a lathe but I know that is not an option for everyone.

regards rog8811
 
Re: Anyone know an easy way to drill through washe

I have done this before! ;D The best way to do it is by firmly securing it to a drill press and slowly lowering the drill into it to get a clean hole. Now, if you want the hole for an axiz module then use a 17/32 drill bit. ;)

--hydro15
 
Re: Anyone know an easy way to drill through washe

rkcstr said:
Drill and bit? I like step bits.

Drill press would be even better.

I use step bits also, but the problem is i cant get a good grip on wasshers without bending them.

I think I might buy a drill press this place called BigLots buy me sells them with a vice for 49.99$

thanks all for the help, Toked323
 
Re: Anyone know an easy way to drill through washe

Try ebay first, I picked up a good one for $21 yesterday (item 220271468767 ) The cheap ones for the DIY market are a bit flimsy sometimes.

Regards rog8811

[edit] I thought I would show you what you can get for £10.50 from ebay ;)[/edit]
 

Attachments

  • Progress02.jpg
    Progress02.jpg
    65.9 KB · Views: 218
Re: Anyone know an easy way to drill through washe

The few times that I've enlarged the hole in a washer, I think I just clamped one (very tightly!) in a vise-grip (locking pliers) and used my drill/step bit to enlarge it.  Also, I've found a cordless impact driver better than a standard cordless drill, like this one, as it doesn't bind up while drilling and drills much faster.

EDIT: when I say clamp in vise grips, I mean clamp to one edge of the washer, NOT try to "hold" it by the edges with the pliers since you will likely not get a very good grip on it that way and it will likely bend if you put a lot of pressure on it.
 
Re: Anyone know an easy way to drill through washe

I start from small drill bits and slowly move up to help prevent the torque of the washer edge catching.
 
Re: Anyone know an easy way to drill through washe

yeah my bosch 18volt impact kicks ass on drilling or anything really.
41Q614D5DPL._SL500_AA280_.jpg
 
Re: Anyone know an easy way to drill through washe

I just resurected this thread to show off my new purchase from ebay, another photo added on a previous post....£10.50....can't be bad ;)

Regards rog8811
 

Attachments

  • Progress01.jpg
    Progress01.jpg
    64.3 KB · Views: 263
Re: Anyone know an easy way to drill through washe

How much did the shipping on that thing cost :-?
 
Re: Anyone know an easy way to drill through washe

Zilch on the shipping, it was 30 minutes up the road from me ;D

Regards rog8811
 
Re: Anyone know an easy way to drill through washe

For better grab, slit the side of a piece of pipe/tubing which fits the od of the washer. Place the washer in the pipe and clamp it with a vice to hold it. A bit extreme but it depends on your needs.

Mike
 


Back
Top