Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Quick Diode Test without driver?

Xer0

0
Joined
Dec 2, 2008
Messages
464
Points
0
As these can take up to 2A without instantly dieing; can you recommend me a kind of Battery which i can use to quickly (for a very short pulse to see if its working) so they dont overheat. I just want to test the harvested diodes fast, dont have a good driver here atm. some Button/Lithium cells maybe?
 





pHeneX

0
Joined
Feb 8, 2010
Messages
162
Points
18
Shouldn't be a problem to test them with a lithium battery (4.2V).

Greets
 

Xer0

0
Joined
Dec 2, 2008
Messages
464
Points
0
An button cell? Cuz an 18650 could pump in more than 3A...
 
Joined
Sep 20, 2008
Messages
17,622
Points
113
Shouldn't be a problem to test them with a lithium battery (4.2V).

Greets
If you test them with only a Lithium Battery at 4.2 Volts without any
current limiting you risk blowing your LD's..

Do you really want to risk blowing a $30-$50 LD by not using a $5.00
Driver...:thinking:


Jerry
 

Xer0

0
Joined
Dec 2, 2008
Messages
464
Points
0
Some guys wanted to resell diodes with me, but they lack the skill to solder an DDL driver, and i dont want to send them some to little-timbuktu ;) So i hoped for a kind of battery, which is so weak, that the maximum currenty would be just enough for see it glimming.
 
Joined
Jun 13, 2007
Messages
5,410
Points
113
You can damage the diode by just shorting it to batteries, and you don't want to send damaged diodes to customers. Just solder a 2 ohm resistor across a LM317 and there you go, a driver to test diodes. Yes I know you said your friend lacks the skills, but it is really easy.
 
Joined
Aug 13, 2008
Messages
361
Points
0
Just to add to that, if you use a 2 ohm resister make sure it's at least 1 watt rated as 2 ohm resister and a LM317 will output 625ma. Be sure the battery input voltage is at least 4.5vdc but no more then 5.5vdc or so.
 

ReNNo

0
Joined
Mar 27, 2009
Messages
589
Points
0
Lm317 need FV+~3V to work...
You cannot give it only 5.5V....
LM317 requires at least 7.5V to work with 445nm diode.

2x18650 should be fine.

btw... you can calculate power of resistor when you multiply current with 1.25V.

For 2ohm resistor, you need 0.78W resistor..so 1W should be fine.
 
Joined
Jun 13, 2007
Messages
5,410
Points
113
The LM317 drops like 3V or so so you have to have at leas 7.5V. Any more voltage than that just gets turned into heat in the LM317.

Edit: ReNNo beat me to it...lol.
 
Last edited:
Joined
Oct 26, 2007
Messages
5,438
Points
83
You're really looking for a non-permanent (i.e. soldering) method for testing these, right? Just buy some machine-pin headers and solder the driver leads to that.

Then before you test, short the two leads, plug the diode in, and turn on the driver. When you're done, pull the diode out of the sockets and you're done. The headers are reusable too.

Batteries are designed to output as much current as the device needs, so you're not going to be able to guarantee any maximum current rating from your batteries (maybe a minimum rating), nearly dead or not. Again, why would you risk a $50 part with some low-quality and dangerous test methodology that can be prevented with $5 worth of parts? It just boggles my mind.
 

oic0

0
Joined
Jun 15, 2010
Messages
289
Points
0
Just wondering here, is it unsafe to use machine pin headers in place of solder permanently on the diode? As in making a quick disconnect module swappable laser?
 
Joined
Apr 28, 2009
Messages
2,416
Points
63
LM317, LM317, LM317...........did I say LM317 yet? Take a look at styropyro's advice. It's ridiculously easy.
 
Joined
Dec 6, 2008
Messages
1,581
Points
63
Xero;

I would just use a 1/2 ohm resistor in series with a 4.2 Volt 18650 battery.

It will drop the voltage an additional 1/4 volt @ 500ma (leaving ~3.85 volts).

Larry
 
Last edited:
Joined
Jan 7, 2007
Messages
6,309
Points
83
Larry has it nailed. There are a few of us who understand Ohm's law and direct drive !!!

HMike

Make sure the resistor can handle .5 to 1 Amp of current. Likely a wire wound.
 
Last edited:
Joined
Oct 24, 2008
Messages
1,057
Points
48
Yeah but that's only assuming the diode will draw 500mA at 3.7 volts.

It's never a good idea to not use a driver but it should work.

-Tony
 
Joined
Jan 11, 2008
Messages
671
Points
0
Xero;

I would just use a 1 ohm resistor in series with a 4.2 Volt 18650 battery.

It will drop the voltage about 1/2 volt @ 500ma (leaving 3.7volts).

Larry

I'm confused. Is Xplorer877 correct that you are assuming the diode will only draw 500mA at 3.7 volts?
 




Top