- Joined
- Dec 15, 2014
- Messages
- 6,782
- Points
- 113
Hi,
Ill send you a PM..
Rich
Ill send you a PM..
Rich
LPF Donation via Stripe | LPF Donation - Other Methods
Links below open in new window
ArcticMyst Security by Avery
Sale thread/ Hosts/Heat Sinks/Focus adapters/lasers
- Thread starter Lifetime17
- Start date
- Joined
- Dec 15, 2014
- Messages
- 6,782
- Points
- 113
FOR SALE.. 35.00 + 5.00 1st class mail
Here is a 1X18650 / 2X18350 host prewired , bored for a DTR 12mm diode and driver.
Thank You Rich
Here is a 1X18650 / 2X18350 host prewired , bored for a DTR 12mm diode and driver.
Thank You Rich
Last edited:
- Joined
- Dec 15, 2014
- Messages
- 6,782
- Points
- 113
FOR SALE.. 40.00 + shipping 1st class mail 5.00
Here is a 2x10440/2XAAA pen host prewired , Holds a DTR 12mm copper module with driver. Also has a custom contact board built in the heat sink.
Thank You Rich
Here is a 2x10440/2XAAA pen host prewired , Holds a DTR 12mm copper module with driver. Also has a custom contact board built in the heat sink.
Thank You Rich
- Joined
- Sep 4, 2020
- Messages
- 1,449
- Points
- 113
Did you remove the tip of that host and press fit the replacement end on it?
- Joined
- Dec 15, 2014
- Messages
- 6,782
- Points
- 113
yes I discarded the entire led and driver portion and bored out the rear to fit snug over the threads of the battery tube. Inside is a custom contact board wired . All is secured by a set screw , this is a great small pen for some single mode diodes. Believe it took a lot of time to machine this small heat sink and recess the contact board.
Rich
- Joined
- Dec 15, 2014
- Messages
- 6,782
- Points
- 113
FOR SALE.. 80.00 + 9.60 Priority shipping
Here is a 1X26650/2X26350 S11 host , deep fin copper heat sink and a see thru focus adapter . It comes prewired with 22 AWG silicon wire. A great stubby host and weighs in with the copper sink and adapter.
Rich
Here is a 1X26650/2X26350 S11 host , deep fin copper heat sink and a see thru focus adapter . It comes prewired with 22 AWG silicon wire. A great stubby host and weighs in with the copper sink and adapter.
Rich
- Joined
- Dec 15, 2014
- Messages
- 6,782
- Points
- 113
BUMP on these...
55.00
30.00
70.00
Copper S11 1x26650/2x26350 65.00
Copper S11 1x26650/2x26350 65.00
- Joined
- Dec 15, 2014
- Messages
- 6,782
- Points
- 113
No I do not , what size battery will you be using? I can machine you a host like the one I just did on page 2,227 that one holds 2x10440 or 2x1.3v
Last edited:
- Joined
- Dec 15, 2014
- Messages
- 6,782
- Points
- 113
BUMP......
Thank you rich
Thank you rich
yes please, that would be good, if possible, can you also make another pen host that fits a 12mm module (using one CR123 battery)
- Joined
- Dec 15, 2014
- Messages
- 6,782
- Points
- 113
So this one and another host to hold 1- CR123 batterie. the CR123 would have to be custom machined or if I can find one for a flashlight modded host. May I can mod one of these host to hold 1-CR123 ..
Rich
Rich
can they both be custom if possible?So this one and another host to hold 1- CR123 batterie. the CR123 would have to be custom machined or if I can find one for a flashlight modded host. May I can mod one of these host to hold 1-CR123 ..
Rich
- Joined
- Dec 15, 2014
- Messages
- 6,782
- Points
- 113
Hi sure so 2- machined customs for 1xcr123 batteries what size module to fit the heat sink
For both hosts
one of them would use a module sized 12mm (diameter) and 56mm (length), also can you make this host similar to this https://ibb.co/XxSk359 if thats fine? can the other one fit a 8mm (diameter) and 35mm (length) module? thanks
- Joined
- Dec 15, 2014
- Messages
- 6,782
- Points
- 113
Hi,
Are both customs? And are the two battery sizes 1x Cr123'S ? And one with a 12mm module and the other at 8mm heat sink??
Are both customs? And are the two battery sizes 1x Cr123'S ? And one with a 12mm module and the other at 8mm heat sink??
