Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

Help sourcing XML emitter?

grainde

grainde

0
Joined
Jan 29, 2012
Messages
3,163
Points
113
I ordered an XML U3 emitter from fasttech back in Jan, but recently had to start a dispute. They claimed to have sent it, but without tracking. It has now been 48 days and there is still no sign of it. :(

Fasttech did refund me after I started a PP dispute, so its not all bad...

Anyway, I need to order a new XML U3 emitter and was wondering where the best and cheapest place to buy one might be? Have already tried Manafont, DX and Kaidomain, and so any other suggestions would be much appreciated! :thanks: :beer:


Edit: Just realised this maybe in the wrong section? :yabbem: Apologies if it is and mods please feel free to move it.
 
Last edited:





Fantastic thanks for that, Ill have a read through.

I might be tempted by a U2 on a copper base...but the only one Ive found is from Ledtech and they charge the earth and then some more for shipping. :( Have you seen them elsewhere? :) :beer:

Edit: Tried to rep you...but the usual!;)
 
Last edited:
thanks for the link Ryansoh3! i've got the U3 on its way from fasttect as well as a driver for my first build which is a solarforce L2P, nothing hard but i am going to be putting it in the empty P60 drop in module. I really wanted to do this build with a XM-L2 but all i could really find was the bare emitter. but if i could put it on one of these copper boards then grind it down i just might give it a shot.
 
Thanks for the link! Ill order a couple of boards too and give it a try. :)

Just curious, I saw that the diodes can be run up to 6 A!! :drool: on these copper boards, so maybe I could give it a bit more power...:eg:

At present I have a 3040 mA board from Kaidomain and Im thinking of maybe combining it with a second AMC board at 1050 mA. Do you know whether they can be paralleled if the current is different? Im also guessing youve built a few of these, so have you also got any advice on switches, as I probably have to use a better one if its running at 4 A...;) :beer:

Edit: @Awillis could you give ryan some rep? I cant and he's been really helpful! :):beer:
 
Last edited:
Would if i could i just gave him some not to long ago for turning me onto fasttech. Yeah thanks alot i've spend about $400 over there in like 2 months. but on a bighter note i've been selling those $10 flashights with an 18650 and charger locally for like $60+ :na:
 
 
Thank you grainde and awillis both for your compliments.

Good luck with your Sinkpad project, can't wait to see it!

Cheers!
 
awillis2589 said:
hey Ryansoh3 what exactly is a COPPER mcpcb? i check out the link and from the picture i couldn't quite figure out how it works? and searching didn't help much either. these might work very well with the XM-L2 because fasttech also has them as bare didodes $5.72 Cree XM-L2 T6-1B 10W 7000K 1052LM LED Emitter at FastTech - Worldwide Free Shipping
Click to expand...

Nice find there! The copper MCPCB is the emitter base (sinkpad), in this case made of copper. Im ordering a couple from here: FS: COPPER mcpcb for XML/XPG High quality boards!!!!!!!!

You need to be able to reflow the LED to the board though...;)

BTW Any ideas whether I can combine 2 AMC drivers in parallel if they have different currents ie 1 A and 3 A or 2 A and 3 A?? Trying to work out how to run these...:eg::beer:


Edit: Just noticed I actually posted the same thread Ryansoh linked for the MCPCB's!:tinfoil: The guy is selling on a few forums...
 
Last edited:
I bought some of these copper pads. They work very well. A XML U2 was soldered to the pad and I have direct drive it with one 26650 cell. It is screaming under 5-6A. :)
They are from the groupbuy in the BLF. Currently they do now the 16mm pad version.

SINKPADS R IN | BudgetLightForum.com
Sink_PAD_Star_XML_copper_zps3c2f3980.jpg
 
Last edited:
@ Blord have you ever used two AMCs with different currents in parallel before? :beer:
 
Graide i think when you want a large amount of amps you have to use direct drive drivers. i could be wrong about this though.
 
grainde said:
@ Blord have you ever used two AMCs with different currents in parallel before? :beer:
Click to expand...

I haven't tried that before. If you want massive current, direct drive is the only way and it is also 100% efficient. No driver in between.
 
You must log in or register to reply here.


Back
Top