Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

How to Register on LPF | LPF Donations

Sale thread/ Hosts/Heat Sinks/Focus adapters/lasers






BUMP!
Don't want members to miss these builds and other custom services:):beer:
 
Hi,
Well With the help of my brother in law and a friend, finally moved the milling machine into the shop. Now just need to set every thing up. My collet set came in yesterday great timing, Also have two sets of end mills for it. Here I go again more tooling:D
@ Alaskan & Red ,
Started turning some AL to 20mm , be better off finding 20mm bar stock.
@ GSS,
Thanks for the :bumpit: Buddy appreciated .
@ SGD,
Thanks for the banner idea though I still have a regular job and really don't want folks to wait to long for items. If I were retired it would be a different story.

Rich:)
 
Hi,
Some pics of a 20mmX1'-3/4 /with 12mm module hole /set screw drilled and tapped .
Sorry Chris was up early no coffee ..

Rich:)
 

Attachments

  • fullsizeoutput_86e.jpeg
    fullsizeoutput_86e.jpeg
    157.3 KB · Views: 14
  • fullsizeoutput_86d.jpeg
    fullsizeoutput_86d.jpeg
    159.2 KB · Views: 16
  • fullsizeoutput_86c.jpeg
    fullsizeoutput_86c.jpeg
    174.2 KB · Views: 15
Say, Rich. Could you make me something similar to the one you made for Chris, but out of copper? I would want a thicker shelf for the BB 8M driver. How much would it cost? :thanks:
 
Paul,
I just made 3 for Chris and he needs 4 , I am going to make Reds over again , I want the shelf to be flush with the bottom of the 12mm hole this way if you want to add a piece of copper to the CU it will come up on spot. These are a PIA trying to get it turned down close to 20mm -/+ , The mill is set for this depth for the shelf but can be raised a bit but I don't see why only because the driver will come almost level with the center. I'll PM you about that question. Some pics of Alaskans sinks. This is my first attempt so be easy on me buddy.

Rich:)
 

Attachments

  • fullsizeoutput_86f.jpeg
    fullsizeoutput_86f.jpeg
    178.7 KB · Views: 10
  • fullsizeoutput_870.jpeg
    fullsizeoutput_870.jpeg
    158.5 KB · Views: 84
  • fullsizeoutput_871.jpeg
    fullsizeoutput_871.jpeg
    175.4 KB · Views: 8
Last edited:
Not bad, Rich. :thanks: I need to see how much room we have to play with and still be inside the bench. It can't be too long.
 
I'm assuming these are good for the 1xdiode community build w/ corrective optics (project #1)? I've got one of those hosts coming, and if this is the ticket, please put me down for 1 as well ;). AL works for me.

Very exciting, Rich. Glad you are getting things set up. New toys for big boys!!! We'll TRY not to inundate you with requests :wave:
 
Lew,
Send me measurements dia.of the sink, sink length and shelf length. We can work at it.

Rich:)
 
Everything is boxed up and put away. I'll have to dig it all out and measure everything. Will do it ASAP.
 
Paul,
No problem I will try a sample in CU using the 20mm X 1" length X 3/4 shelf measurement.

A CU addition had to try it out.. Enjoy...

Rich:)
 

Attachments

  • fullsizeoutput_878.jpeg
    fullsizeoutput_878.jpeg
    164.1 KB · Views: 8
  • fullsizeoutput_879.jpeg
    fullsizeoutput_879.jpeg
    158.4 KB · Views: 7
  • fullsizeoutput_87a.jpeg
    fullsizeoutput_87a.jpeg
    149.8 KB · Views: 8
Last edited:
If you get it, Chris, let me know how well the alignment works out with it. I was considering buying it too, but want to know if the alignment works or not. I have a feeling it will wok fine. Just want some confirmation before I buy one because if it didn't work, I would have no other use for it.

Didn't mean to hijack your sales thread, Rich.
 
You must log in or register to reply here.


Back
Top