Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

Pioneer 8X Blu-Ray-- BDR-203

They are two different diode brands for one thing...

But even when comparing my diode against the other BDR diodes so far, mine is lower in efficiency.

We get this with other blu-ray diodes as well. Like the PHR's and even the 6X diodes. Some are higher in efficiency than others. Igor's first 6X was a low efficiency diode. But it is also a very 'tough' and long lasting diode! :)

Hopefully my 8X BDR is that way...
Jay
 





Five enlisted, two more to go...

...because it was the seven Samurai, last time I checked... ;)

...and I'm sure Igor will close the group by being the seventh, so we need just one more...  8-)
 
As soon as I have sold off enough of my PHR stock, (And get a 405-G-1) then I will be joining the group. And, like WannaBurn, I am working on a boost driver for this output level (I need one for a seperate LED-based project, but it shouldn't be too hard to adapt it...)

Sadly, I don;t expect we will see any of these drivers produced for a few months.
 
Jack89: If you are offering something for sale it should go in the buy/sell/trade section of the forum. If you want help identifying your sleds you should post a new thread on the help/tutorials section of the forum. Please do not spam random threads with pictures of your sleds.

Another thread already exists for discussing your sleds. It can be found here: http://www.laserpointerforums.com/forums/YaBB.pl?num=1240405492
If you have any meaningful information to post about these sleds, please post it there.
 
pseudolobster said:
[quote author=Jack89 link=1236464366/384#406 date=1240455789]oh, very sorry, my English not good, ignorant of how to operate, very sorry
Click to expand...

No problem, welcome to the forum. [/quote]


THANK YOU VERY MUCH!
 
charlie bruce said:
...then I will be joining the group. And, like WannaBurn, I am working on a boost driver for this output level (I need one for a seperate LED-based project, but it shouldn't be too hard to adapt it...)
Click to expand...

Cool, looking forward to your success stories :D
 
Franko --

Good work on that compilation of data for the 8x.  I used that tonight.

I received my "203" today and it looks like Dave's except for the IR part which looks more like a sensor.

I removed the 405 and noticed that there was a microscopic crack in the window.  May be me or the fact that it is " refurbished".  Oh well.
Mounted in a Kenom head with a Jayrob lens ----------

mA   Po  mW
    200  243
    250  300
    300  365
    320  400
    340  424
    350 437
I think this is looking similar to JayRob's data.  I may have found the knee in the curve.  Dave got a HOT one  :D

Mike
 
And Quantile's BDR is even 'Hotter' than Dave's!

Well, I don't feel so left out anymore Mike. ;D

Just kidding... I'm plenty happy with the power! Man, if you got that baby in a Kryton, you better watch your fingers at that power! Kind of hard to focus a Kryton without getting your fingers in the way huh?
Jay
 
I could make something up especially for your Kryton Mike... (oh wait a minute, you have a lathe) Check this out...

Do you have the focus ring on there? Because I was thinking that an o-ring/press on type thing, like this little fiber optic pencil idea that I was experimenting with:

fiber optic pencil.jpg


It just pushes onto an AixiZ focus ring and stays on very well. It has room in the side wall thickness to fit inside the Kryton head! :)

So you could easily make it fit the same way with the o-ring, but the part on the outside, could be about the same size in diameter, as the Kryton head. Now the I.D. of the Kryton heads, are the same for both the Groove as well as the 1st run Krytons, but the O.D. is a different size, so it would have to be sized for either a Groove, or a 1st run Kryton! ;)
Jay
 
Jay --
I will make an extender on my lathe. It's too hard to adjust the focus with that G1 lens while it's on. My fingers get too hot ;D Others might appreciate the extention.

Mike
 
Hemlock Mike said:
Franko --

Good work on that compilation of data for the 8x.  I used that tonight.

Mike
Click to expand...

Modified - graphic added in reply # 392.

Thank you Mike. With your data, I have tried to trace an "efficiency comparison" of the various 8x diodes. With the exception of Intro74 diode, the efficiency of which looks to be abnormal (does it comes from a different manufacturer?) the other diodes are quite lined-up (I have traced an "average line").... see the annex. As Quantile data have been recorded with an Aixiz acrylic (not the 405G1) lens, the slope of the average line will change.....

Concerning the focusing ring extension, it's a really good idea also in case of less powerful lasers... I remember that IgorT has shown something similar in one of his pictures.... an extension having quite the same external diameter of the host.... maybe these extensions are already available from him....
 
@ FrankoRob: Nice graph but there is one fundamental flaw: to compare efficiency you can't compare different mA levels - since laser diodes change their efficiency at various current levels, (and temperature age, etc). The best way of doing this comparison would be to get readings at identical levels - say a reading at 100, 200, 300 and 350mA. If everyone is willing to do this, then this comparison could really help us to get a better understanding of these diodes.
 
charlie bruce said:
@ FrankoRob: Nice graph but there is one fundamental flaw: to compare efficiency you can't compare different mA levels - since laser diodes change their efficiency at various current levels, (and temperature age, etc). The best way of doing this comparison would be to get readings at identical levels - say a reading at 100, 200, 300 and 350mA. If everyone is willing to do this, then this comparison could really help us to get a better understanding of these diodes.
Click to expand...

Modified
Yes, you're right, the term "comparison" is not right, this graphic give a simple visual overview of the "points" relevant to the data (mW/mA) that the diode owners declare in this Forum. Of course I'm available to plot a new graphic as the data you suggest will be available, also if the results will still not be completely comparable, (different drivers, different Power meters, etc.).
In the meanwhile, I'm going to upgrade the datasheet with Mike and I'll move there also this point plot graphic.... :)
 
Had a busy time at work - no time to play with lasers, so my 405-G lens had to sit on the desk for a week :(

Finally got to try it out, here are some 405-G measurements of my 8x, appear to be consistent with what has been reported so far:

I/mA       P_o/mW
100         104
...           ...
150         195
...           ...
200         282
210         297
220         314
230         330
240         350
250         367
260         383
270         402
280         415
290         430
300         452
310         464
 
You must log in or register to reply here.





Back
Top