- Joined
- Jul 10, 2015
- Messages
- 9,961
- Points
- 113
My original 07e died early run at only 3.4 - 3.6 amps, but I now again happily bask in it's sky blue glow.
Last edited:
Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers
Buy Site Supporter Role (remove some ads) | LPF Donations
Links below open in new window
FrozenGate by Avery
NUBM07E How I have missed thee.
- Thread starter RedCowboy
- Start date
- Joined
- Feb 26, 2015
- Messages
- 1,359
- Points
- 0
sound like she don't like people messing around with G-spot...
- Joined
- Feb 26, 2015
- Messages
- 1,359
- Points
- 0
some one is selling a 10x beam expander for $150
- Joined
- Feb 26, 2015
- Messages
- 1,359
- Points
- 0
Eforce laser for the beam expander... they are coated...
Pman
0
- Joined
- Nov 28, 2012
- Messages
- 4,441
- Points
- 113
Where did you find that MX900 for $15? I've only seen them for at least twice that much.
- Joined
- Dec 9, 2011
- Messages
- 221
- Points
- 28
I found that my 07's were just slightly out of focus with the gball. It is very easy to "re-focus" the g ball with 2 positive lenses. 07=====()===()====> . Adjusting the distance between the two positive lenses can bring the diode into perfect focus. I didn't try, but am guessing it can help focus at a distance.
Pman
0
- Joined
- Nov 28, 2012
- Messages
- 4,441
- Points
- 113
Thanks for the MX900 link. Had one host and 2 sinks so needed another one. It's not that easy to find decent switches.
Nice vids and pics too. +REP
Nice vids and pics too. +REP
- Joined
- Mar 21, 2016
- Messages
- 964
- Points
- 43
Hi Red, at what current were you running your nubmo7e?
- Joined
- Jul 10, 2015
- Messages
- 9,961
- Points
- 113
I run mine at 3.5 amps and use a SXD driver, I would love to run a whole block of these, the color is great.
The Gball on the nubm06 focuses pretty well to about 1/4 by 1 inch at 15 feet but the 07e is about 1 inch by 2 inches at 15 feet with it's Gball, they look the same removed, but the 07e likes the G7 from SANWU
I had deleted 60 videos and 620 pics early April 2016 so I will clean up what I can and start over, they nubm07e is a gorgeous wavelength, much brighter looking than 450nm.
NUBM07e with G7
NUBM07e with G7
The Gball on the nubm06 focuses pretty well to about 1/4 by 1 inch at 15 feet but the 07e is about 1 inch by 2 inches at 15 feet with it's Gball, they look the same removed, but the 07e likes the G7 from SANWU
I had deleted 60 videos and 620 pics early April 2016 so I will clean up what I can and start over, they nubm07e is a gorgeous wavelength, much brighter looking than 450nm.
NUBM07e with G7
NUBM07e with G7
Attachments
Last edited:
- Joined
- Mar 21, 2016
- Messages
- 964
- Points
- 43
I was thinking about running one at 4 amps, what ya think about what kinda life i'd get out of it?
- Joined
- Jul 10, 2015
- Messages
- 9,961
- Points
- 113
The factory data sheet says 3.5a Max so you would think 4.0 would be no problem, they do make a bit of waste heat and power stops going up but spectrum shifts. Hold on I will see, I think Cypragon posted a graph.
By the charts 4.0a looks ok, I use the SXD it has a ramp up cap, if you ask DTR about the driver he can tell you what will work best, but 4.0 should be ok, but if its a hot pull vs a cold pull it may not last as long or it may, I think the more you stress anything the sooner it will fail, so if yours is hot pulled I would stop at 4.0, but that's just my guess. I could be wrong, mine has 2 small lines in the raw output, but they seem to have healed. Right now it's going strong.
I know DTR cold pulls his, I prefer cold pulled, but I also like a good deal, so far this hot pull of mine is doing well.
Really it should be ok, just don't cook it.
By the charts 4.0a looks ok, I use the SXD it has a ramp up cap, if you ask DTR about the driver he can tell you what will work best, but 4.0 should be ok, but if its a hot pull vs a cold pull it may not last as long or it may, I think the more you stress anything the sooner it will fail, so if yours is hot pulled I would stop at 4.0, but that's just my guess. I could be wrong, mine has 2 small lines in the raw output, but they seem to have healed. Right now it's going strong.
I know DTR cold pulls his, I prefer cold pulled, but I also like a good deal, so far this hot pull of mine is doing well.
Really it should be ok, just don't cook it.
Last edited:
- Joined
- Jan 17, 2011
- Messages
- 62
- Points
- 0
I have this diode. It's going into a MX-900(Thanks Red.) Just waiting for my heat sinks to be finished up and shipped back to me. I'm going to be running it at 4A with a "potted" driver. I love my 462nm this should be even better.
Its goi
Its goi
- Joined
- Jul 10, 2015
- Messages
- 9,961
- Points
- 113
Are you using that adjustable black buck driver?
- Joined
- Mar 21, 2016
- Messages
- 964
- Points
- 43
Who is making your heatsink?
- Joined
- Mar 21, 2016
- Messages
- 964
- Points
- 43
Just got my s4x in, man it's beefy. Whole things a heatsink. Getting ready to order some diodes/drivers. Been carrying around a 35mm lens out of a flashlight I tore down for a host. Have found several flashlights that can host the 35mm module
- Joined
- Jul 10, 2015
- Messages
- 9,961
- Points
- 113
I saw an Ozark trail 3 C cell that looks like it should be close to 35mm at the head, the tube would take 2x26650.
But I am planning a bigger multi diode build, I would like to use a whole block...I would like to stack 2 blocks of 06's and use big round double concave / double convex lens and see what I can do with it.
If prices keep falling, soon I will strike. :eg:
But I am planning a bigger multi diode build, I would like to use a whole block...I would like to stack 2 blocks of 06's and use big round double concave / double convex lens and see what I can do with it.
If prices keep falling, soon I will strike. :eg:
