Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

(No Longer A Distributor) PL Series Modules From Lasever (LAB/Industrial)

Re: FS: PL Series Modules From Lasever (LAB/Industrial)

Excellent.

Cant wait to see your build. :beer:
 





Re: FS: PL Series Modules From Lasever (LAB/Industrial)

HippyHop said:
Excellent.

Cant wait to see your build. :beer:
Click to expand...

Yep I'll be showing it soon...

I did a 'Hot' option set up for ZRaffleticket with his 473nm module. So he may be able to 'shed some light' on beam diameter and divergence... :D

Edit: Check out his beam shot comparison with his labby added to the first post... :)
 
Last edited:
Re: FS: PL Series Modules From Lasever (LAB/Industrial)

What's the stability on these? From what I can tell, what makes 473s nasty is that they are really unstable after 30-45 seconds and then won't like being turned on for a little while. Can you do a 1.5 minute laserbee test of them?
 
Re: FS: PL Series Modules From Lasever (LAB/Industrial)

Based on mine, I wouldn't run it longer than 30s. I'll pull out my LPM equipment and do a measurement of mine ^
 
Re: FS: PL Series Modules From Lasever (LAB/Industrial)

Yeah I think it's best to just use a duty cycle...

I have a habit of using a duty cycle with all hand held lasers. It's a good rule of thumb. :)
 
Re: FS: PL Series Modules From Lasever (LAB/Industrial)

Jay. What is the dimensions of that blue cap/switch on the board? How far does it stick up off the board?
 
Re: FS: PL Series Modules From Lasever (LAB/Industrial)

jeffreythe00 said:
Jay. What is the dimensions of that blue cap/switch on the board? How far does it stick up off the board?
Click to expand...

Just carefully pry the blue cap off of the switch plunger with a small screw driver...

Then you can just turn the switch on, and it will not stick out past the edge of the board. :)
 
Re: FS: PL Series Modules From Lasever (LAB/Industrial)

I'm asking because I was planning on using it :)
 
Re: FS: PL Series Modules From Lasever (LAB/Industrial)

jeffreythe00 said:
I'm asking because I was planning on using it :)
Click to expand...

Oh I see said the blind man...

In the off position with the blue button on there, it sticks out 6.5mm past the edge of the board. And in the on position, 4.5mm...
 
Last edited:
Re: FS: PL Series Modules From Lasever (LAB/Industrial)

Hey Jay,

I've got a buddy looking for an astronomy pen. When I starting looking, I noticed there are fewer and fewer reliable sources around anymore. Does lasever have anything like that available to you? Anything we could piece together into a pointer?
 
Re: FS: PL Series Modules From Lasever (LAB/Industrial)

Meatball said:
Hey Jay,

I've got a buddy looking for an astronomy pen. When I starting looking, I noticed there are fewer and fewer reliable sources around anymore. Does lasever have anything like that available to you? Anything we could piece together into a pointer?
Click to expand...

Not sure about that for Lasever...

But I have pen hosts that you just get your green module for: :)
http://laserpointerforums.com/f64/fs-new-pen-host-kits-switch-board-spring-option-nice-22561.html
 
Re: FS: PL Series Modules From Lasever (LAB/Industrial)

Yay Found it! Awesome modules and builds. These look awesome!
 
You must log in or register to reply here.





Back
Top