FS: New Pen Host Kits! Switch board with Spring Option - Nice!

[jayrob]

Price drop! (now $11 ea.)

These pen hosts are brand new and very clean.

They would be perfect for building a blu-ray or a red pointer using a FlexDrive with 2 X AAA batteries.

You would have to modify a small board and fit the included momentary switch, add a small spring for contact, etc... but not a problem if you have some basic building skills. (Board not included)





Switch board with spring option:




Here's an option for this build that will make it really easy to do the assembly! It is a blank board, fit for the black plastic switch mounting piece. It has a momentary switch and spring contact already mounted! Add $3 dollars for this option. (see below)





Note: These are available in black with chrome clip, or all chrome as well!

Update: I found out that the 'all chrome' ones are only available with the extra hole above the side button. This means that they are a little longer at the front. Like 1/4" or so. These would be easier to fit an O-like module. But the O-like module would still need to be shortened.



The hole is easily covered with a warning label or sticker...




If there is interest in these Pen Hosts, I will stock about 10 at a time, and have them on hand.

* $11 dollars plus $3 dollars shipping.
* Add $3 dollars for each switch board with spring.
* Add $1 dollar shipping for each additional Pen.
* Please read my shipping policy here!





Don't forget lens options!:

* 405-G-1 glass lens mod - $55 31% increase for blu-ray vs AixiZ acrylic! (new) See link in signature!
* 650-G-1 glass lens mod for red! (fit for AixiZ) - $52 25% increase for red vs AixiZ acrylic! (new) Shown here: http://laserpointerforums.com/f64/fs...ase-46332.html

I must warn, if you have not built a Leadlight or a pen build before, I just want to warn you that they are very small builds and do require some decent building skills. Mostly understanding how to set current on a FlexDrive with a proper test load like many other builds, but the smaller the build, the harder it is. Getting the button just right can be a little tricky with pens.

That said, with these brand new kits, you can start with all new parts, and not have to take one apart, possibly causing damage!

These Pen Hosts are easy builds if you have some basic building skills...





Update:

I just got the 'all chrome' ones too. So I have both on hand...

Same price as the black with chrome clip pen hosts.

The chrome ones are a little longer at the front, and have an extra tiny hole above the side button that can easily be covered with a label.

[wannaburn]

Do you have any of these availible now? Also will there be any discount for bulk and if the switch is not needed?

Id be interested in a few of these.

[jayrob]

I don't get a break on the price unless I buy 50 at a time...

And the switches I just had already and was just giving them away. I don't think they will cost me much if I end up needing more. Maybe .50 cents or so. (I hope)

I have the one (sample) on hand, and can have a many as you want with-in 2 days.

I will definitely give a combined shipping price though...
Jay

[pullbangdead]

Just when I think you couldn't come up with anything else I could want this week, you pull out another nice pen host, in a nice matte black no less. It seems all the black pens out here have gold on them, which I just don't like, but this black with silver clip would look great.

[jayrob]

;D They are a very nice clean Pen Host!

Here's another picture that I will add to the 1st post...


Jay

[leukoplast]

Oh, I like. Might have to get me one of these.

[jonasa0601]

I might be interested in 2 of these..

When someone have it, please post a small review here

[jayrob]

These are very clean hosts...

Brand new, no scratches or anything. They are available with or without the small hole above the side button. I will order some without the hole, because I suspect that most will not want the extra hole there...

[Milos]

very nice. I'm interested in 4+

[nastynick]

for the momentary switch, you would wire it in before the flexdrive, correct? positive or negative?

[jayrob]

I am offering these as hosts with the parts shown for DIY... I believe I can get chrome ones too! 8-)

So no 'Hot' options or anything, but yes, you would test the switch to find out which contact points will connect when you press the button. Then you know which will be connected to your spring (battery contact), and which will be the lead to your FlexDrive.

You can use a DMM to test for continuity first.

Pens are small, and do require good building skills. Not necessarily impossible if your new, but not considered a really 'easy' build. (IMO)
Jay

[Spyderz20x6]

Jayrob has done it again! :P
I would be interested in 1 without a hole above the button.

[jonasa0601]

@jayrob

Damn, that's to bad I just started soldering, and my skills are low..

I also just started getting into electronics, so maybe i can't do it with this host :'(

[jayrob]

Ok...

Sounds like there is some interest here, so I will order at least 10 or maybe 20 black with chrome clip. And see about the possibility of chrome as well.

Go ahead and PM me with orders, and I will get a list going for this first order.

Then I will plan on stocking a few for quick shipping!
Jay

[The_Muffin_Man]

I would be interested in one without the hole above the button. Black please

[jayrob]

Originally Posted by jonasa0601

@jayrob

Damn, that's to bad I just started soldering, and my skills are low..

I also just started getting into electronics, so maybe i can't do it with this host :'(

I do have some othere kits that are easy builds!

You could start out with the popular 4171 or 3405 host. I have options that include FlexDrives installed and current pre-set if you want...

See here:
http://www.laserpointerforums.com/fo...m=1233442476/0
Jay

[jonasa0601]

@jayrob

38$ is more than i will give for a host+heatsink, even though i know that it is what they cost.
I will max give around 25 bucks for the host+heatsink, but maybe that isn't possible.
If i run a LPC diode so it will put out 250mW, will it get hot in those builds you mentioned in the link?

[jayrob]

The heatsinks have plenty of mass for the 'Hottest' diodes that we are currently using!

Just PM me if you change your mind since this thread is about these new pen hosts! 8-)
Jay



P.S. I just ordered 12 black with silver clip, and 1 black with gold clip. (no extra hole above the side button)

I will have them by Monday. So these first ones will got to the first ones who PayPal me. Contact me via PM.

I asked about the all chrome ones too, and they are also available. More to come...

[culexor]

Would I need to do anything other than shorten the module if I wanted to stick an O-Like module in one of these (like anything with the button, etc.)

[XCreedX]

Those are some beast pen kits jay 8-) I am defiantly going to buy some, can't beat the price either

[jayrob]

Sure thing! Just let me know...

Originally Posted by culexor

Would I need to do anything other than shorten the module if I wanted to stick an O-Like module in one of these (like anything with the button, etc.)

You would have to fit the plastic piece shown in the 1st picture (switch/driver mount) so that it actuates the button switch on the o-like module. It would be an easy modification. It almost just snaps into place. There would just be some light trimming here and there with an X-acto blade...
Jay

[The_Muffin_Man]

Are there any left? I am interested.

Could you use a rkcstr instead of a flexdrive (using 10440 batteries)? If it is like a regular leadlight it should be fine.

[jayrob]

Yes, I'm sure there would be room...

I plan on keeping a few on hand for fast shipping, but new stock will only be a couple of days away. I will have these first 12 by Monday and ready to ship.

At this moment, yes, these are available. They are black with chrome clip.
Jay

[Kenom]

I don't think those are anodized. *Looks to me like the body is brass and if that's the case then it's not anodized although they do look very zexy. *I've got a ton of these switches here.



Wow! that's a big picture.

[jayrob]

Oh... I didn't realize that Ken.

The finish is so nice, that I assumed it was anodized. But it is a brass host. I just changed the caption in my first picture to say 'Satin black finish'
Jay