Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

GB: $16 Aurora C6 kits

If you're using my driver you need 2x 16340 cells.
Although, the voltage drop for the regulator is suppose to be 1.5v at 3A.
If its low enough at 1A you might get the minimum voltage tequired with one cell but I highly doubt it.

You got a message on PF :shhh:
 





Hey VisibleGreen!

Hey! do NOT run it at 946mA, Mine did not LED, it still runs and I am going to drive it lower.
I had been using it on and off from like 20-60seconds and probably totaling 5 minutes since I built it, last nite it was snowing very lightly and I wanted to get some outdoor shots with it and the 445 rubber banded together :)
I had stuck them into the freezer for about 10 minutes and they were cold, I put them on top of a brick that had been outside - which I placed on the hood of my van and then placed the lasers on there and ran them for about 3 minutes while I shot photos.
They were not even warm when I was finished. After I got inside had turned the red on and quickly observed it rapidly going dim, thinking the batteries had died I stuck a fresh set
in and it dimmed quite quickly! I waited half an hour and it did the same thing.

So, I am just hoping I can setup a driver for it at lower current now.

I hope you read this!



Got the hosts. The heatsinks fit perfectly! According to LaserCo they are fit for 635 diodes



So the diode is ok with 3.7 volts or does the driver adjust? Your setup was exactly what I was going to do with the 946 setting. You're using a single cell I assume. How much in mw does it provide?

Sorry for all the questions... just need to make sure :)
 
PM sent

Hey VisibleGreen!

Hey! do NOT run it at 946mA, Mine did not LED, it still runs and I am going to drive it lower.
I had been using it on and off from like 20-60seconds and probably totaling 5 minutes since I built it, last nite it was snowing very lightly and I wanted to get some outdoor shots with it and the 445 rubber banded together :)
I had stuck them into the freezer for about 10 minutes and they were cold, I put them on top of a brick that had been outside - which I placed on the hood of my van and then placed the lasers on there and ran them for about 3 minutes while I shot photos.
They were not even warm when I was finished. After I got inside had turned the red on and quickly observed it rapidly going dim, thinking the batteries had died I stuck a fresh set
in and it dimmed quite quickly! I waited half an hour and it did the same thing.

So, I am just hoping I can setup a driver for it at lower current now.

I hope you read this!
 
I've got parts on hand. But things are in hiatus due to my wife making us go on vacation :(
 
I've got parts for 13 kits that can ship before I leave for vacation. after that, They will have to wait until I get back.

I have added the available stock to the website. If you're able to purchase it, it's available.

All orders placed before Feb 12th will be shipped out before I leave.
Everything place after Saturday will be shipped when I return on Fed 25th.
Mohgasm.com
 
Last edited:
I need to do a better job of editing threads once the buys are complete.

They are periodically available at my website, though they are never $16.....
 
I've got laser engraved c6 hosts and cnc machined and black anodized heatsink on the way. Will be here in about 2 weeks, probably less.
 
I've got laser engraved c6 hosts and cnc machined and black anodized heatsink on the way. Will be here in about 2 weeks, probably less.

How many are you getting Moh? will they be on your site for purchase? because i see you have another thread for engraved c6 and i thought they were limited time only and in limited quantities :cryyy:

Please chime in on this.

thanks - gif
 





Back
Top