Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

FS: Pocket Mini Build Kit! - Easy Assembly!

Ok so I just turned on the laser for approximately 30 seconds and this time I think I felt a very little warmth on the very top of the head at 23 seconds. but it was only a bit, maybe nothing. it wasnt warm after i turned it off too.Strange.
 
Last edited:





Sounds like it's fine...

Your going to get a little warmth after 30 seconds or a minute with your red build. That's why I always use a 1 minute on / 1 minute off duty cycle.

Igor has mentioned that a duty cycle may not be necessary when he was testing blu-ray diodes. But I figure it can't hurt! (he never finished explaining his theory though)
Jay
 
Hey thanks for extra info and I have to say I am doing like 10 min duty cicles off and then using my laser for max 30 secs everytime. Its simple. I don't have anything do with it if I run it that often. so I just leave it to rest xD
 
Two pill pieces??

You mean the round battery contact board to the pill?

In the first post of this thread, it is a 'picture tutorial' of the assembly. Plus there are some 'Build tips' at the bottom of the post as well...
Jay
 
No the thing holding the driver to the thing holding the diode.

Do you glue it or somthing??
 
Only if you cannot screw the assembly into the head of the host without letting the wires get twisted...

You could use a very small amount of adhesive to connect the heatsink to the pill, but I have found that it is not necessary, because you can 'pinch' the assembly tight together between your thumb and ring finger.

See the 'build tips' in the first post.
Jay
 
whats a pill?
if its the power bit could i buy a hot option just the pill and the flexdrive preset?
i am willing to pay how ever much it would cost
 
Last edited:
The pill is part of the host, it holds the round battery contact/circuit board, and is what the emitter is mounted on...

Take a look at the 6th picture down in the first post of this thread, and you will see a picture of how it is slightly modified for this build.

I would recommend just getting the complete kit. Host/heatsink/drill the pill. Then the 'Hot' option includes the installation of a FlexDrive into the pill with lead wires ready, and current set as shown here:
http://laserpointerforums.com/laser_pointer_forums_3/forum/showthread.php?t=22537&page=5#108
Jay
 
wwslubs, just to let you know that your Pocket Mini kit with 'Hot' option is shipping today. (Monday)

I have the driver set at 125mA's per you request...

Post back when you do your build! :)
Jay
 
pikapfw, your Pocket Mini basic kit is shipping today. (Tuesday)

Post back when you do your build! :)
Jay
 
PJ Kash, your Pocket Mini kit with 'Hot' option is shipping today with your 405-G-1 glass lens and other item. (Wednesday)

Set at 180mA's per your request. (blu-ray test load)

I hope your build goes well! Maybe post back with some pictures huh?

:thanks:
Jay
 
JensT, I am shipping your Pocket Mini kit with 'Hot' option (and other item) today. (Thursday)

I have it set at 90mA's per your request. (blu-ray test load)

Hope you build goes well! :)
Jay
 
jeffd, I am shipping your Pocket Mini kit with 'Hot' option today. (Wednesday)

I have the driver set at 125mA's per our discussion...


I know you guys must be loving these builds... Sure would like to hear back from more of you guys! :)
Jay
 
You must log in or register to reply here.


Back
Top