Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers



FS: FIFTY 5-25mW 8x13mm red modules, OVERSPEC! and dirt cheap!

lasersbee

Well-known member
Joined
Sep 20, 2008
Messages
17,708
Points
113
Keep this up Jerry and I am going to start a ban poll for you!
You had better put a smiley on the end if that statement....:whistle::D

Jerry
 



Krutz

New member
Joined
Nov 21, 2007
Messages
1,733
Points
0
good work, th0ughts!

interesting, isnt it? it all worked out, more or less, at the beginning. then, once there was public interest, and several people having an eye on him, there is almost no sentence where he is *proven* to lie!

manuel
 

Invader Zim

Member
Joined
Jul 23, 2009
Messages
115
Points
18
A while ago I bought a phr in an aixiz module from Tyler's store and I ran it it at 120mA with a rckstr driver, it immediately led'd. I told him and he said 120mA was too high for a phr but I thought he knew much more than me about lasers so I left it at that but now I'm not sure if 120mA is too much. I think I remember reading somewhere on this forum that 120mA is OK. It was just a phr in an aixiz module so it doesn't matter much but I want to get things straight.
 

mfo

Banned
Joined
Jul 3, 2009
Messages
3,402
Points
0
A while ago I bought a phr in an aixiz module from Tyler's store and I ran it it at 120mA with a rckstr driver, it immediately led'd. I told him and he said 120mA was too high for a phr but I thought he knew much more than me about lasers so I left it at that but now I'm not sure if 120mA is too much. I think I remember reading somewhere on this forum that 120mA is OK. It was just a phr in an aixiz module so it doesn't matter much but I want to get things straight.
I believe anything over 100mA with a PHR is a gamble. Now please...let this thread slip into the depths of the forum never to be seen again....
 

daguin

New member
Joined
Mar 29, 2008
Messages
16,573
Points
0
A while ago I bought a phr in an aixiz module from Tyler's store and I ran it it at 120mA with a rckstr driver, it immediately led'd. I told him and he said 120mA was too high for a phr but I thought he knew much more than me about lasers so I left it at that but now I'm not sure if 120mA is too much. I think I remember reading somewhere on this forum that 120mA is OK. It was just a phr in an aixiz module so it doesn't matter much but I want to get things straight.

The vast majority of the PHR modules I sold were run with fixed 120mA Rkcstr drivers.

Peace,
dave
 

Invader Zim

Member
Joined
Jul 23, 2009
Messages
115
Points
18
WTF? I got neg rep'd because I said OK then.



"Stop intentionally bumping drama threads & spamming."


This is like the second time I've posted in months. I think.
 

robjdixon

New member
Joined
Feb 29, 2008
Messages
2,364
Points
0
well whoever did it, is obviously not so good of a person themselves! just immature or jealous, so they felt the need to add those immature tags to this thread, thinking it will phase me. nice try though ;) keep on going guys, I'll stiiiiiiil be here :D

Good luck!
Lol fail
 

Krutz

New member
Joined
Nov 21, 2007
Messages
1,733
Points
0
*bump*
why? because its a forum, i am a member, and the thread is open.
that negative rep was unnecessary. +1 for zim.

manuel
 

mfo

Banned
Joined
Jul 3, 2009
Messages
3,402
Points
0
*bump*
why? because its a forum, i am a member, and the thread is open.
that negative rep was unnecessary. +1 for zim.

manuel
Why? Because we're trying to put all of this Tyler bullshit behind us, that's why. Check the vets section Manuel and see how many fights were set off in there because of that prick. That's why we need to stop posting in these Tyler related threads and just let it go already.

@Invader Zim: It was quite obvious that that "OK then" was quite uncalled for.
 

Invader Zim

Member
Joined
Jul 23, 2009
Messages
115
Points
18
What about "Stop intentionally bumping drama threads & spamming." WTH is that, huh? So you neg rep'd me for saying OK then?
 
Last edited:

Mohrenberg

New member
Joined
Aug 30, 2008
Messages
6,924
Points
0
i run all my modules at 120mA (or 117 depending on the SMD resistors i have on hand), 120mA should not LED it, and he should of replaced it.

Highest i've gone with a PHR is 175mA, and i think dave got one freakishly high on accident.
 

Invader Zim

Member
Joined
Jul 23, 2009
Messages
115
Points
18
I thought 120mA was shortening it's life but not kill it. Oh well it does not matter much anymore.
 

lasersbee

Well-known member
Joined
Sep 20, 2008
Messages
17,708
Points
113
Why? Because we're trying to put all of this Tyler bullshit behind us, that's why. Check the vets section Manuel and see how many fights were set off in there because of that prick. That's why we need to stop posting in these Tyler related threads and just let it go already.

@Invader Zim: It was quite obvious that that "OK then" was quite uncalled for.
Hey mfo....

if you want to end this thread then use your energy like me... and
send a PM to c0ld and ask him to lock a thread... instead of Neg Repping
members that post on the open thread...

Just a thought...:whistle:


@ Invader Zim... have you seen the Title of this Thread... It has nothing to
do with PHR803T Blu-Rays... or did I miss something...:thinking:


Jerry
 
Last edited:

mfo

Banned
Joined
Jul 3, 2009
Messages
3,402
Points
0
Hey mfo....

if you want to end this thread then use your energy like me... and
send a PM to c0ld and ask him to lock a thread... instead of Neg Repping
members that post on the open thread...

Just a thought...:whistle:


@ Invader Zim... have you seen the Title of this Thread... It has nothing to
do with PHR803T Blu-Rays... or did I miss something...:thinking:


Jerry
Now you know why I did what I did Jerry....
 




Top