Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

Dorcy Jr- Blu-Ray!!

not that difficult. I'm presently working on installing a pot into the bluray so I've got an adjustable bluray for this and do what you suggested and make a swappable head.
 





I am placing the resistors/pot into the original factory module, so the module is completely self-contained, the rest of the flashlight, including the head-body, is completely unmodified. In this way, these are already swapable with another module-set-up, or even the entire head, as you describe, if desired. This may be what you are saying anyway.
My favorite location to place a resistor so far is replacing the little yellow ground-wire, with a resistor, or set of resistors twisted together. This works really well, and with a little carving, a small pot may be placed here as well, but since this is the ground-side, you must be careful not to short your heat-sink, (which would be grounded), to the flashlight body. This would bypass your resistor-pack, I believe.
Anyway, fun-stuff ;)
Dark Horse
 
the only problem I have with putting the pot in the original driver or down inside the battery section is that you have to adjust the resistance before putting in the new module. When showing off my lasers I don't wanna have to mess around with adjusting something then showing just plug'n'play baby. Your idea of putting the resistor on the negative wire is intrigueing but won't work for my heatsinks since they do indeed come in contact with the ground. There is no doubt that there are plenty of places if a person is creative to place a small potentiometer. I have a 50 ohm potentiometer that is SMT. So it's gonna fit right on the board. I'm hoping that it fits right on the positive end. I'll take pictures to show what I've accomplished.
 
I have a fixed resistance in mine. I think a total of 154.5 ohms instead of a POT, 35mA.
 
the only problem I have with putting the pot in the original driver or down inside the battery section is that you have to adjust the resistance before putting in the new module.  When showing off my lasers I don't wanna have to mess around with adjusting something then showing just plug'n'play baby.
Click to expand...
That's exactly what I was trying to say, just not very well I'm afraid. ;) I only modify the module-(that slides out of the head). To change a module, you would unscrew the head, slide out the "diode-module-assembly", slide in a new one, and you should be set for a new laser/LED light, because all of your resistors, or whatever, are only in the diode-module, (or you could just change the entire head). But I keep thinking, what good would this be, other than just the "coolness" of it? I modify mine in this way more because of my philosophy to maintain as much of the original design as possible. I like being able to "rip" the whole thing down in front of someone to explain exactly what you have done, and snap it back together ;D. I guess this would kinda be like the guys with the show cars, except I don't have a mirror under my hood ;D
Dark Horse
 
ya know the one downside of having both modules in one is that you have one battery compartment/section that goes to waste. Now luckily I have a lot of left over components from these builds but if you didn't you would have to go out and buy 2 flashlights to build one laser.
 
here's a picture of the bluray with a pot in it.  it's a 100 ohm pot.  I started at 40 ohms and dialed it down until I achieved the desired output of 15mw.  not a clue what the current is TBH

DSC00095.jpg
 
Kenom,
Thats perfect, is that on the positive or negative side of the diode?
Dark Horse
 
Positive.  I actually used the positive pad to connect the pot to.  it's a bit hard to tweak the pot but it can be done.  I had to cut down the plastic rings that go around the star. but it works perfect.
 
i have a dorcy jr, i cut the spring to see if i can connect it to a diode, it has a shaft collar drilled out and stuck in it. i am asking 17.50$ shipped to anyone as-is though. maybe you can do something with it
 
this isn't a for sale thread toked. Post it in the appropriate section please.
 
I see where this idea is going... Kenom, what if one were to put a 6x Blu-Ray burner diode in there...
 
Not capable of producing the current AND the voltage I think.
 
Kenom said:
Not capable of producing the current AND the voltage I think.
Click to expand...
The voltage would be the same. Higher power LDs don't take a higher voltage, they take a higher current. So why not? I'm guessing a 6x blu-ray runs at about 100mA from jayrob's calculations, so a 12-15 ohm resistor should do fine...
 
Spyderz20x6 said:
The voltage would be the same. Higher power LDs don't take a higher voltage, they take a higher current. So why not? I'm guessing a 6x blu-ray runs at about 100mA from jayrob's calculations, so a 12-15 ohm resistor should do fine...
Click to expand...

As the current goes up, so does the voltage.
 
You must log in or register to reply here.


Back
Top