Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

List of 445nm diodes

No problems SHIN

use the method I described and your reading and settings will be dead on!
 





Just fyi, I'm in Italy for the next 10 days, so I can't update the chart in that period of time.
 
A130
New 445nm coated AixiZ glass lens
1.037A -- 1.042W

I'll do some more tests with my A140 once I get a larger heatsink.
 
A130
Micro Flex Drive v5
800mA
Aixiz acrylic lens (I think that is what lens MarioMaster used when taking the power measurement)
715mW (avg)
Old style Modwerx heatsink
Has been alive since the 2nd of July
 
Name: laserboystuart
Diode source: XJ-A130
Driver: MicroBoost
Current: 900mA
Lens: 405-G-1
Power: 946mW
Host/Heatsink: Jayrob 18650 Cu
usage time: <1 hour

stuart :)
 
Holy crap! I'm so excited now to start my 445 build. I plan to use the 18650 host, a140 at about 1.1A and aixiz 405 glass :D
 
bhank said:
Holy crap! I'm so excited now to start my 445 build. I plan to use the 18650 host, a140 at about 1.1A and aixiz 405 glass :D
Click to expand...

That's close to what I'll have. Right now I am soon to have an 18650 kit (plus Aixiz 405 glass) and I have a Flexdrive at 1.2A and an A130 diode. But I might just turn the pot on the Flex to 1.5A after seeing nospin's results.
 
A140
Romisen 14500 host
pressfit heatsink by IgorT
950mA
455nm coated aixiz glass lens

Estimated output: ~1W

Not bad for a "AA" sized host :P
 
Last edited:
Finally updated again, with one especially interesting build (1,6W)
 
Name: Kevlar
Diode source: XJ-A130
Driver: MicroBoost
Current: 900mA
Lens: 445nm Aixiz
Power: ?? (no LPM) :cryyy:
Host/Heatsink: Ehgemus Custom/Al
usage time: ~2 hours
 
That's close to what I'll have. Right now I am soon to have an 18650 kit (plus Aixiz 405 glass) and I have a Flexdrive at 1.2A and an A130 diode. But I might just turn the pot on the Flex to 1.5A after seeing nospin's results.
Click to expand...

I'd have to agree ZRTMWA! I'm personally just taking my time on this build mainly because I'm waiting until my next paycheck to order the diode and flex, all I've got ordered right now is the 18650 host kit from Jayrob and the aixiz 405 glass lens.

It is quite difficult to wait though, after seeing everyones builds here I've been drooling for the past week and a half haha! :drool:
 
Mine :

Jayrob CR2 Stainless Polished, copper heatsink
375ma, Flexdrive v5
approx. 200mW
A130 445nm diode
status : Alive
Lifetime 0h (no battery yet)
 
Diode Source: XJ-A130
Driver: FlexDrive V5
Current: 1.5A
Lens: Aixiz 405 Glass (Jayrob Custom)
Power: No LPM
Host/ Heatsink: Jayrob 18650 w/ XL Copper Heatsink
Run Time: <1 hour
Status: Alive

So far I am not heatsinking my FlexDrive because I'm not sure of the best method. The laser only stats to blink on longer duty cycles, around 90-120 seconds on. I think I'm going to use thermal pads.
 
Last edited:
#3
XJ-A140
microflex v5 1150mA
405-G-2 lens
heatsink - custom P60
powered by 18650
LPM - Kenometer lite
Output power after lens - 1250mW

#4
XJ-A140
microflex v5 1180mA
405-G-2 lens
heatsink - custom P60
powered by 18650
LPM - Kenometer lite
Output power after lens - 1300mW

I use my new custom 2A test load to set the v5. (4 of iN5404 and 1ohm resistor=4V)
I could not set over 1.2A. So I asked drlava about this.
Drlava's microflex v5 can supply maximum 1.2A to 445nm LD, not 1.5A.
This is described as a equation at the last lines of v5 manual.

SHIN
 
You must log in or register to reply here.


Back
Top