GB: 2$ copper modules ALL SIZES CLOSED

[Machinist Joe]

Like I have said before, If dtr would like to sell me all the modules he got, I can shorten all of them easily.

Also, I think we should triple check how much we are actually going to take off of these. DTR do you have a dial caliper? We could measure the height from the bottom of the bore (bottom of where the lens screws in) to the top (where the focus adapter sits, and then do the same for a standard aixiz and know exactly how much to take off.

I don't want us to go too small after being too big...

 

[ped]

I have a brass Aixiz 9mm I can send you if it will work. It's gonna cost you though, $0 and one "pay it forward."

Whooosh....straight over my head :crackup:

Explain, PM if you want haha dont wanna derail the thread.

 

[tsteele93]

Whooosh....straight over my head :crackup:

Explain, PM if you want haha dont wanna derail the thread.

I'll send you a 9mm Aixiz module for free. Just do something nice for someone else when you have the chance sometime in the future. That is the "pay it forward.".

 

[AnthoT]

Thanks for everyone's patience :beer: I'm doing my best to fix this and I'm sure it will turn out great! Hopefully not too long of a delay as well

 

[ped]

I'll send you a 9mm Aixiz module for free. Just do something nice for someone else when you have the chance sometime in the future. That is the "pay it forward.".

Sounds like a deal to me :beer:

 

[AnthoT]

I think that I need the std sizes as well, but I would be willing to also buy some of the long versions as well. That way I could help cut your losses AND I could use the long ones on low power builds where an acrylic lens would be ok.

Is there a way to just order some of the "longs?"

The 445 single modes are 3.8mms, right?





I have a brass Aixiz 9mm I can send you if it will work. It's gonna cost you though, $0 and one "pay it forward."

Thats very kind of you tseele I'm sure ped appreciates it, its a great way of paying it forward :beer: i'd +rep you but the system said no

If you'd like long modules let DTR know, he's got them all

Like I have said before, If dtr would like to sell me all the modules he got, I can shorten all of them easily.

Also, I think we should triple check how much we are actually going to take off of these. DTR do you have a dial caliper? We could measure the height from the bottom of the bore (bottom of where the lens screws in) to the top (where the focus adapter sits, and then do the same for a standard aixiz and know exactly how much to take off.

I don't want us to go too small after being too big...

Its a very kind offer thank you :beer: the only issue i see is then after you machine them down the threading will be a bit messed up.... Its a kind offer and i appreciate it very much :beer: i'd +rep you but i can't as i recently did (for the spreadsheet) and the system said no

 

[tsteele93]

Sounds like a deal to me :beer:

AND... I just noticed you are in the UK. I can still send it free, but I don't know how long it takes. I don't know how much faster it will get there vs waiting for the copper modules.

The offer still stands though, PM me your address and I will drop one in the mail tomorrow. I sent something to Blord once and it wasn't expensive at all.

 

[AnthoT]

Guess what

they can be all fixed and shipped by the end of the week!!! :wave:

We have also reordered all the 3.8 & 9mm for the US in correct sizing

I still apologize for the delay... i really didn't want to have any issues but its been solved and confirmed

:thanks: for everyones patience

 

[kiyoukan]

if those ones that dtr has needed to be changed let me know i got my lathe and i can rig up a quick way to take that 4mm off.

 

[AnthoT]

if those ones that dtr has needed to be changed let me know i got my lathe and i can rig up a quick way to take that 4mm off.

I dont know what will happen to those.... It's up to DTR, we have a new batch coming in so maybe those could still be sold as a fixed focus heatsink for a pen build or a labby fixed focused module

 

[bennett326]

if you have any long ones 5.6mm you want to sell i will take a few these are perfect for labbies you could sell a bunch on PL with out a doubt :beer:

 

[AnthoT]

if you have any long ones 5.6mm you want to sell i will take a few these are perfect for labbies you could sell a bunch on PL with out a doubt :beer:

DTR's got quite a few 3.8mm & 9mm left from what I know only about ~30 sold so far but those Id assume are all available for sale to anyone

 

[bennett326]

DTR's got quite a few 3.8mm & 9mm left from what I know only about ~30 sold so far but those Id assume are all available for sale to anyone

thanks ill shoot him a pm

 

[AnthoT]

thanks ill shoot him a pm

No problem

 

[kiyoukan]

well those ones dtr has are 3.8 and 9mm not many lab styles for those.
Thinking if im going to put them on my lathe i would just make them 5.6mm diode holders.
Well its up to DTR and you

 

[AnthoT]

well those ones dtr has are 3.8 and 9mm not many lab styles for those.
Thinking if im going to put them on my lathe i would just make them 5.6mm diode holders.
Well its up to DTR and you

I'll leave that up to DTR, he has the modules with him and if you'd like you can contact him for them, machine them to 5.6mm if you'd like and use them, but that's up to you. If you wanted them then DTR definetly has enough on him at this moment.