- Joined
- Jan 24, 2016
- Messages
- 22
- Points
- 0
Hello Guys,
i want to introduce you finally my finished Build .
Here are the List of the Compontents i Use:
- Nichia NDB7875 in Copper Module with G2 lens :drool:
- Super X Drive V3 Buck :san:
- Efest IMR 18350 V2 800mAh
- Convoy C8 Flashlight
- Custom Heatsink :drool::angel:
- Eagle Pair 190-540nm safety google OD6+ :beer: cause safety First
- Extendet Focusing Ring
- Custom Handmade Lanyard from me with 550 Paracord
I think i need no explaination of the Diode, Module,Batterys and Safety googles.
The Super X Driver was Thermally attached to the Heatsink with Arctic MX4 Thermal Grease which i use for every thermal attachment :drool:. For fixing it, i put little dots of 2k epoxy on the sides of the Driver.:drool:
For the Contact Board i took an Nanjg 16mm Driver and cut all interconnects with the Dremel. Only Thing i left there was the Negative pads of the AMC chips which i Bridged for Better resistance. After that i drilled a small hole for the Positive Wire to the Brass Pill which my Friend also machined me.
the interesting thing is the Heatsink. It is Machined out of Aluminium, then little "cooling" fins was milled in and then filled up with a mix of 2k epoxy and GITD powder. After that the Aluminum was Drilled out for Pressing a Copper shell in. The Copper shell was now drilled to 12H7 with a reamer for a nice finish. After that the set screw was placed with a milling machine. After all it gets a nice polished finish but at assembly i put some scratches in... But you guys know that stuff to well ..
The Host is an normal Convoy C8 Flashlight with integrated Head. The spring on the Tailcap was bridget with silicone Wire 0,25 mm² and the Complete Soldering was done with Sn99Cu1+ML. I Switched the O rings and Tailcap rubber to a Green GITD for nicer Look. :angel:
At the first current measurements at the Tailcap it Draws about 1.8A @ about 8,4V . seems to be ok
But at the first outside test without googles and good caution. "My Eyes just pop out " It is many better and nicer then i tought. Im so completely happy with this Build its soo fun. Nice Beam , cool Look. More then i expect thank you all guys for helping me.:san::drool:
a special thanks for DTR and Survivallasers for giving me good Quality parts really Fast. And enable me this nice build. :san::san:
But enough words, i let pictures speak :angel:
BTW: All Units are Metric
Thank you Guys,
Hope you enjoy it i do
Best regards
Nico
i want to introduce you finally my finished Build .
Here are the List of the Compontents i Use:
- Nichia NDB7875 in Copper Module with G2 lens :drool:
- Super X Drive V3 Buck :san:
- Efest IMR 18350 V2 800mAh
- Convoy C8 Flashlight
- Custom Heatsink :drool::angel:
- Eagle Pair 190-540nm safety google OD6+ :beer: cause safety First
- Extendet Focusing Ring
- Custom Handmade Lanyard from me with 550 Paracord
I think i need no explaination of the Diode, Module,Batterys and Safety googles.
The Super X Driver was Thermally attached to the Heatsink with Arctic MX4 Thermal Grease which i use for every thermal attachment :drool:. For fixing it, i put little dots of 2k epoxy on the sides of the Driver.:drool:
For the Contact Board i took an Nanjg 16mm Driver and cut all interconnects with the Dremel. Only Thing i left there was the Negative pads of the AMC chips which i Bridged for Better resistance. After that i drilled a small hole for the Positive Wire to the Brass Pill which my Friend also machined me.
the interesting thing is the Heatsink. It is Machined out of Aluminium, then little "cooling" fins was milled in and then filled up with a mix of 2k epoxy and GITD powder. After that the Aluminum was Drilled out for Pressing a Copper shell in. The Copper shell was now drilled to 12H7 with a reamer for a nice finish. After that the set screw was placed with a milling machine. After all it gets a nice polished finish but at assembly i put some scratches in... But you guys know that stuff to well ..
The Host is an normal Convoy C8 Flashlight with integrated Head. The spring on the Tailcap was bridget with silicone Wire 0,25 mm² and the Complete Soldering was done with Sn99Cu1+ML. I Switched the O rings and Tailcap rubber to a Green GITD for nicer Look. :angel:
At the first current measurements at the Tailcap it Draws about 1.8A @ about 8,4V . seems to be ok
But at the first outside test without googles and good caution. "My Eyes just pop out " It is many better and nicer then i tought. Im so completely happy with this Build its soo fun. Nice Beam , cool Look. More then i expect thank you all guys for helping me.:san::drool:
a special thanks for DTR and Survivallasers for giving me good Quality parts really Fast. And enable me this nice build. :san::san:
But enough words, i let pictures speak :angel:
BTW: All Units are Metric
Thank you Guys,
Hope you enjoy it i do
Best regards
Nico
Last edited: