Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

PLUG & PLAY CO2 BURNING LASERS only $150 DELIVERED

Re: GB LIVE & OPEN for Small RF 5-10W CO2 LASERS!

I got mine today too !!!  Packaging to the 10's  ;D

Nightstick -- are you running PWM or just 5v on the control line?  You are seeing what I get from my 15 mW (WATT updated) HV CO2.

I'm excited.    Thanks Chris............

Mike
 





Re: GB LIVE & OPEN for Small RF 5-10W CO2 LASERS!

Mike, you mean ma? not mw right? :-?
 
Re: GB LIVE & OPEN for Small RF 5-10W CO2 LASERS!

OOPS --- 15 Watt HV CO2.
15 mW CO2 ???? :D

Mike
 
Re: GB LIVE & OPEN for Small RF 5-10W CO2 LASERS!

ya, the HV is only about 15 ma isn't it? :)
 
Re: GB LIVE & OPEN for Small RF 5-10W CO2 LASERS!

about 12 mA for 15 Watts. Burned the coffee table :( OOPS.
Mike
 
Re: GB LIVE & OPEN for Small RF 5-10W CO2 LASERS!

Mike Im running 4volts with a wall type power supply it starts plywood on fire real quickly the cloth towel fired right up also disma your gona love this thing still running off batteries 25.90 volts now :)
 
Re: GB LIVE & OPEN for Small RF 5-10W CO2 LASERS!

Holy crap --- I may have smoked the coating on my Scientech sensor.
Same voltages as Nightstick.  I only ran it for 2 bursts of 5 seconds and even I'm impressed.  I've got to select a better thermal head for this beast.

Mike

Try to keep stuff a couple feet from the output coupler so it doesn't get damaged by smoke or flying crap !!

This does need PWM.  It has no analog slope.  It's either ON or off.
 
Re: GB LIVE & OPEN for Small RF 5-10W CO2 LASERS!

Mike can you explain pwm Im lost thanks Lynn :-/
 
Re: GB LIVE & OPEN for Small RF 5-10W CO2 LASERS!

PWM -- Pulse width modulation.  A TTL driver circuit with the on /off ratio varying between ~ 5% and 95%.

Chris recommends 24 kHz at 90% duty cycle.

Mike
 
Re: GB LIVE & OPEN for Small RF 5-10W CO2 LASERS!

I need that Now I just ahave to figure out how to make it or is it ok to run this the way I am :)
 
Re: GB LIVE & OPEN for Small RF 5-10W CO2 LASERS!

Lynn --

Depends on your heatsinking.  I think CW is OK if you have fans and good heat disappation.
The instructions say best efficiency at 24 kHz and 90% on cycle.
Watch your heatsinks and keep the time on cool until we have more info on power control.  
How many fans do you have on yours?
Mike

I was thinking of using a 555 timer chip as my PWM but I think there are chips more suited to the purpose.
 
Re: GB LIVE & OPEN for Small RF 5-10W CO2 LASERS!

Mike right now just one big one and I keep feeling the laser and the heat sink and as long as I keep my on time to 5 sec burst it stays fairly cool just a little warm to th touch
 
Re: GB LIVE & OPEN for Small RF 5-10W CO2 LASERS!

Mike keep me informed on this ttl if you dont mind, Im not sure on what to get yet for this.,, when you all figure it out I could really use the help thanks :)yes and Chris does pack a mean Box, thanks again Chris and thanks to Scopeguy for telling me about this GB
 
Re: GB LIVE & OPEN for Small RF 5-10W CO2 LASERS!

The PWM input current is about 25 mA. Almost any TTL design will easily drive it.

Warning: As Chris stated -- this will set fire to almost anything in seconds. Know where it is pointed. Do not let it hit the couch or stuffed chair. This is not a toy. Please use a safe beam dump back-up for the target. Even unfocused, it packs the photons............

Mike
 
Re: GB LIVE & OPEN for Small RF 5-10W CO2 LASERS!

Good idea on the switch.  Put it in the PWM line or you will need a BIG 10 Amp switch in the mains line.

Mike

Lynn - Do you wear glasses? Plastic?? Be careful of your eyes. I'm dumping mine almost point blank into a power meter.
 
You must log in or register to reply here.


Back
Top