andy_con
0
- Joined
- May 24, 2007
- Messages
- 3,394
- Points
- 0
time for me to clear some stuff out as i have to much stuff.
6x diode holder milled from a single block of aluminium. currently there isnt a back but its sold with a back plate to hold the diodes in, ill mill that up.
70mm long x 12mm wide x 27mm high
11mm spacing between diode holes - ddiodes holes drilled for 5.6mm diodes and tapped at 9x0.5 thread
3x m3 mounting holes on the bottom
after £60 + shipping - thats £10 per diode holder so good value
quad diode setup made from aluminium. not sure if someone can use this or not, it could be turned into a red and blue module
diode holes drilled for 5.6mm diodes and tapped for 9x0.5 thread
total sizes - 141.5mm long x 66.5mm wide x 45mm high
after £80 + shipping
2x round aluminium projector windows
one is 70mm dia with a 57mm dia inner
one is 49mm dia with a 39mm inner
£15 each (gee these cost me a lot)
quad 660nm red module
one or two of the diodes have gone so they will need replacing, but its only a 10min job.
apart from the diode(s) this module is fully working.
produces a 3.5mm by 3.5mm beam @ 0.65mR
142mm long x 65mm wide x 40mm high
after £300 + postage
1watt 445nm module
this is a one off module, you wont find another like this. i made it as a bit of a test module. 0 hours on the clock and fully working.
1watt at 5mm by 5mm beam @ 0.55mR
59mm long x 42mm wide x 39mm high
beam height of 16mm
made with a die4laser driver so analogue modulation. comes with a required 6.5v psu
after £300
laserpic Z30 scanners
full spec here -
Galvo, Scanner, Scanning, laser show,laser projector at laserpic
fully working with a number of hours on the clock.
30k scanners have done me very well over the years.
not sure what they are worth so make me an offer
1watt 445nm laser module
ive got two of these for sale
Output Power - 1000mw
Wavelength - 445nm
Beam Size at Aperture - 5mm
Divergency - 0.55mR
Modulation - 30kHz analogue and TTL
Polarization - V
Operating Power - 6.5v @ 1.5a
Module Dimensations - 80mm (L) x 55mm (W) x 35mm (H)
The Module comes with the necessary mains PSU, input voltage 100-240VAC
i normally sell these for £350 but im offering them for £320 at the moment + shipping
6x diode holder milled from a single block of aluminium. currently there isnt a back but its sold with a back plate to hold the diodes in, ill mill that up.
70mm long x 12mm wide x 27mm high
11mm spacing between diode holes - ddiodes holes drilled for 5.6mm diodes and tapped at 9x0.5 thread
3x m3 mounting holes on the bottom
after £60 + shipping - thats £10 per diode holder so good value
quad diode setup made from aluminium. not sure if someone can use this or not, it could be turned into a red and blue module
diode holes drilled for 5.6mm diodes and tapped for 9x0.5 thread
total sizes - 141.5mm long x 66.5mm wide x 45mm high
after £80 + shipping
2x round aluminium projector windows
one is 70mm dia with a 57mm dia inner
one is 49mm dia with a 39mm inner
£15 each (gee these cost me a lot)
quad 660nm red module
one or two of the diodes have gone so they will need replacing, but its only a 10min job.
apart from the diode(s) this module is fully working.
produces a 3.5mm by 3.5mm beam @ 0.65mR
142mm long x 65mm wide x 40mm high
after £300 + postage
1watt 445nm module
this is a one off module, you wont find another like this. i made it as a bit of a test module. 0 hours on the clock and fully working.
1watt at 5mm by 5mm beam @ 0.55mR
59mm long x 42mm wide x 39mm high
beam height of 16mm
made with a die4laser driver so analogue modulation. comes with a required 6.5v psu
after £300
laserpic Z30 scanners
full spec here -
Galvo, Scanner, Scanning, laser show,laser projector at laserpic
fully working with a number of hours on the clock.
30k scanners have done me very well over the years.
not sure what they are worth so make me an offer
1watt 445nm laser module
ive got two of these for sale
Output Power - 1000mw
Wavelength - 445nm
Beam Size at Aperture - 5mm
Divergency - 0.55mR
Modulation - 30kHz analogue and TTL
Polarization - V
Operating Power - 6.5v @ 1.5a
Module Dimensations - 80mm (L) x 55mm (W) x 35mm (H)
The Module comes with the necessary mains PSU, input voltage 100-240VAC
i normally sell these for £350 but im offering them for £320 at the moment + shipping
Last edited: