510 side button modification

[Lifetime17]

hi Folks,
i would like to elaborate on the happy wife thing. Well the saying is true but not 100% of the time believe me my brothers. But its all good we make plans and God laughs. They always have something up their sleeves. I think i need a new crystal ball isn't working from time to time. But i wouldn't change a thing LOL !!!

Rich

 

[BobMc]

hi Folks,
i would like to elaborate on the happy wife thing. Well the saying is true but not 100% of the time believe me my brothers. But its all good we make plans and God laughs. They always have something up their sleeves. I think i need a new crystal ball isn't working from time to time. But i wouldn't change a thing LOL !!!

Rich

That's too true also Rich!
As the song goes "a man needs a maid". (Just don't say I said so).

 

[3DLaSeRBuiLDeR]

I would explain as you pull out the cap of the + ? in 510

 

[Lifetime17]

hi,
3d All you have to do is take off the 510 adapter and push the Pos+ pin out with a small punch, Done its isolated from the Neg- adapter it self..

Rich

 

[3DLaSeRBuiLDeR]

hi,
3d All you have to do is take off the 510 adapter and push the Pos+ pin out with a small punch, Done its isolated from the Neg- adapter it self..

Rich

Grazie Rich :beer: , voglio provare a costruire anche io un 510 modulo...!
Di certo non verrà bene come quelli che costruisci tu...però ci voglio provare !

 

[Lifetime17]

Ciao 3D,
The Pos+ is adjustable to a limit setting it high just enough toehold the wire , them screw it down till it makes contact and that 510 will be set for that particular vape mod

Riccardo

@BM,
I won't say word buddy to funny..

Rich

 

[3DLaSeRBuiLDeR]

Ciao 3D,
The Pos+ is adjustable to a limit setting it high just enough toehold the wire , them screw it down till it makes contact and that 510 will be set for that particular vape mod

Riccardo

@BM,
I won't say word buddy to funny..

Rich

Ok Riccardo ! I ordered already the aluminum now do you see what I got !

 

[3DLaSeRBuiLDeR]

What do you think about this tube ?

 

[Lifetime17]

Hi
Its 9mm ID and a copper module that holds the diode is 12mm. So if you intend to use it for heat sinking you will have to bore out the hole.But I think you will need a thicker wall seems to thin for a 9mm diodes heat

Rich

 

[3DLaSeRBuiLDeR]

Hi
Its 9mm ID and a copper module that holds the diode is 12mm. So if you intend to use it for heat sinking you will have to bore out the hole.But I think you will need a thicker wall seems to thin for a 9mm diodes heat

Rich

Hi,
For the flaring of the diameter I will use a spiral to enlarge the holes in the HSS , then with my "cut tubes" manual I will cut the piece with a length of 5cm ! and then the block with 2 drills and I run at medium / high speed and carve of the lines as it is to yours
I unfortunately do not own a lathe, for metals ..!

 

[Lifetime17]

Hi 3D,
Cant wait to see how the build comes out, this is a way i never seen before. Before i had a lathe i would do the same type of modding to get these results also. Many members here are very good with adapting to build without a lot of tooling , and some of the builds are awesome. Keep at it and when your done post some pics buddy.

Rich

 

[3DLaSeRBuiLDeR]

Hi 3D,
Cant wait to see how the build comes out, this is a way i never seen before. Before i had a lathe i would do the same type of modding to get these results also. Many members here are very good with adapting to build without a lot of tooling , and some of the builds are awesome. Keep at it and when your done post some pics buddy.

Rich

I certainly hope only that I will be good !
Anyway, a little place a new "jewel" this time it's a 1.5 W - 405nm

 

[Lifetime17]

Hi, Yes I just seen the 405 nice job buddy with what was on hand

Rich

 

[3DLaSeRBuiLDeR]

Thx Rich !