PontiacG5's Massive sales thread. Diodes, Lasers and parts!!

[Pontiacg5]

Hey everyone! Long time no see, eh?

If anyone was wondering I finally found the opportunity I was looking for and I've been working pretty much non stop since the work is there. I might have a few machines of my own before much longer, assuming I can get enough saved up for a down payment. Since I want to make sure I get those machines I'm going to sell most all of my laser stuff. I won't have much time to put any of these projects together anytime soon anyway, hopefully

I guess I'll start with my stray diodes...

First, I have 5 A140 445 diodes. I am asking $40 shipped for these.

Next, I have a 2W 808 C-mount diode and a few crystal sets. This diode is brand new, still sealed in an anti static bag. I’ll be including a 473nm crystal set in good condition and a higher powered 532nm crystal set with a burned out NdYVO4 crystal. This green module assembly doesn’t use bonded crystal sets so you can replace the NdYVO4 and get quite a bit of power out of it with this 2W diode. The Blue set is from a CNI module, 2W of pump power should make 10+mW of 473nm blue. I’m going to ask $75 shipped for the diode and two crystal assemblies.

Next, I have a brand new 500mW 635nm c-mount diode. This diode does not have a FAC but I will be including a cylindrical lens that can be used with an aixiz lens to get a halfway decent beam. I’m going to ask $75 shipped for this one, with the cylindrical lens included.

Next, 5 LOC sleds. These are the older LOC diodes but I can’t remember the exact numbers. These sleds are all untouched, still in the original boxes. I’m asking $25 shipped for all 5.

Next, a bag of random IR diodes pulled from PHR or SF-AW sleds. $5 shipped gets these. No idea how many there are, but it should be more than 5.

I also have three old PHR (The case neutral version) diodes and two SF-AW diodes. The PHR diodes are harvested and still have the ribbon soldered to the pins. The SF-AW diodes are still in heatsinks and need harvested. I’m asking $20 for the 4 PHR diodes and $20 for the two SF-AW diodes. SF-AW SOLD


That’s it for diodes, next is whole lasers…

Next, I have two 635nm 20mW diodes. These are brand new diodes, the pins have never seen solder. I’m going to ask $25 for both of these shipped. SOLD

Next, a big bag of random 9mm diodes. There should be ~30 in this bag. I have no idea what is in the bag and I don’t know how many will actually work properly. I’ll be including 6 of my copper 9mm modules with these. I’m asking for $25 shipped for this set. SOLD

Next, I have a bunch of the e-bay 638nm diodes. I have no idea what any of them will actually do, but I know none are 638nm. There are 7 of these diodes, all marked at different power levels. They are all still sealed in anti static bags, never used. I am going to ask $20 shipped for these, they’d make very good diodes for a first practice build. SOLD

Next, I have 3 638nm 35mW diodes, supposed to be new. They are pressed into some metal tray if I recall correctly. You should be able to search the forum to learn a little more about these diodes since I forgot what they were! I’m going to ask $20 for all three of these shipped. SOLD

 

[Pontiacg5]

Regrettably, I think I am going to sell my two CNI pen lasers.

The second is a Wicked Lasers “Fusion” from way back in the day when Wicked sold decent lasers. It was originally rated for 125mW but for some reason at SELEM I couldn’t get it to meter higher than 90mW or so. That might be the batteries, might be the laser, really no way to tell. The brass is starting to go and the button is rather chewed up but it still has amazing divergence and a super fine beam. I’ll be sending this one in a Wicked Lasers box as well except this box will come with the outer paper sleeve. I’m asking $125 +shipping for this laser, probably pretty high but it is still a great laser and you can’t buy them like this anymore (at least I think so, CNI’s quality seems to have turned to crap.) If I can’t get $125 for this one I’ll just keep it. In fact I hope nobody offers me anything for it, I want to keep it

Next, a laser I built pretty recently. It has a 445 diode with a maxed out grooveV2 driver in a pen host. I used one of my copper modules with the aluminum back half for this build, for maximum cooling. The driver itself will go into thermal shutdown before the laser gets hot, that happens in approximately 45 seconds, after 10-15 seconds the laser will be good for another 30-45s of lasing fun. I would guess this thing is making close to 500mW with the aixiz glass lens. This thing needs two 10440 batteries to run, I have two that will be included but they are pretty much shot. You WILL need new 10440 batteries! I’m asking $125 shipped for this pen.

Next, I have a 473nm “lab” laser. You may be familiar with these things from e-bay. It works and is pretty stable after a brief warm up period but the divergence needs work, big time! I’m asking $75 shipped for this one, only because it is really sable and I’ll guarantee that it works (unlike e-bay!)

[sale pending IMG]http://i879.photobucket.com/albums/ab357/pontiacg5_2010/IMG_20111126_210601.jpg[/IMG]

Lastly, I have a Uniphase 2214-40MLA argon laser with a “golden” 110V 2214-40MLA power supply. Included is a homemade control panel and a few A140 fans for cooling, everything you need to start lasing multiple lines of argon beauty. This laser does 75mW+ and normally does around 7-8 lines depending on tube current. This thing is HEAVY! so shipping will be pretty expensive. If you live within a few hours of me I’ll deliver this guy for $350, if not I am asking $300 + insured shipping costs. sale pending

That’s it for lasers I have for sale, next is laser accessories and just flat out random stuff!

The first is a 593.5nm, rated for 3-5mW. It works absolutely amazing, it’s rock stable and never shifts to 532 as I have heard other 594nm lasers do. I’ve had this laser for years, 5+ years to be exact so it does show a little wear. The paint is flawless, not a single bubble or chip as I guess new CNI pens do. The rubber button is not all chewed up as I have seen other CNI pens do. The Brass is the worst part, it’s getting rather tarnished and worn off over the years. I did stick the little blue sticker that originally came over the aperture over the end of the tailcap so it should look pretty good under that sticker. I’ll be sending this laser in an original “wicked lasers” wooden box because I somehow have a few extra.

I’m really not wanting to sell this laser, but I don’t use it very much (at all) anymore. It hasn’t been on since SELEM and probably won’t be turned on till next SELEM. I’m going to ask $200 +insured shipping for this one. SOLD

Next, I have a PHR module with a cheap boost driver. Stick it anywhere with 3V and it’ll do 75-100mW, no soldering needed. I’m asking $10 for this one. SOLD

 

[Pontiacg5]

Next, my laser safety glasses (ha!) This will probably get me flamed but I really don’t care what side of the safety glasses debate you stand on. These glasses block enough red, green and blu/blue light that I felt safe enough using my lasers up close with them on. Will they take a direct hit? Probably not. Do they work better than no glasses? You betya. I’m asking $25 shipped for all 4 pairs.

[sale pendingIMG]http://i879.photobucket.com/albums/ab357/pontiacg5_2010/sales/phrdrivers.jpg[/IMG]
[sale pendingIMG]http://i879.photobucket.com/albums/ab357/pontiacg5_2010/sales/200mA.jpg[/IMG]

Next, some drivers. I have three Jib drives; 444mA, 379mA, and 500mA. $10 shipped each. Next, some cheap 100mA boost drives for PHR diodes. I think there are 10 total. I’m asking $10 shipped for all of those. I also have two similar drivers but set for 200mA instead of 100mA. Those will be free with the PHR drivers. sale pending on PHR/200mA drivers

[sale pendingIMG]http://i879.photobucket.com/albums/ab357/pontiacg5_2010/sales/glasslens.jpg[/IMG]

Next, I have a blue aixiz glass lens. This lens is brand new, still in the paper it came in. I’m asking $5 for this lens with the purchase of anything else. sale pending



Well, that's almost all I have for sale right now. Like I said above most of these prices are negotiable so just PM me an offer.

I don't plan on leaving for good, I never really will I won't be around much at all anymore in the near future. I almost always reply to e-mails though, just in case anyone has to get in touch with me for some reason...

First, some silicon wire and matching heat shrink. No idea exactly how much wire and heatshrink is there but it will be more than enough for any and every laser build you ever plan on doing! The wire is white and blue, came from Moh, and the heatshrink is red, black and white. I’m asking $15 shipped for all of this stuff. SOLD

Next, some batteries and cheap chargers. This all will be sold as a set. There are 4 16340’s, two cheap 18650’s, three cheap 18650 chargers and two very nice, new, AW IMR 14500 600mA batteries. I’m asking $15 shipped for all of this stuff, less than what I paid for the IMR 14500’s if I remember right. SOLD

Last, a few hosts. One is a C6 with a bad tail switch. The other 4 are working AA flashlights. I forget who it was but someone built a sweet tiny laser in one of these hosts so I had to try it. I never actually tried it though… $10 shipped for all of these. SOLD

Next, a cool little disc that glows under laser light. I can’t remember exactly what it is called but I got it off e-bay 5 years+ ago. It will glow under laser light for around 20-30 seconds before it dims out. I remember this thing being expensive but I don’t remember exactly how expensive. I’m asking $20 shipped. If you know what this thing is please speak up! sold

Next, everything you need to build a LPM. There are a few PCBs as well as all of the components needed to build the meter. A panel mount volt meter is included, and unlike most other meters this one can measure it’s own power source. (it is isolated by a buck/boost circuit) This way your LPM only needs one source of power unlike some of the other meters that need 2 different sets of batteries. A super tiny super high junction count TEC is included as well. The very small size with large numbers of junctions will make the meter react to inputs a whole lot faster than most other TEC based meters. I’m asking for $65 shipped for all this stuff. Remember, you will need to think of some way to calibrate this meter once you build it. I picked multi turn bourns pots instead of the single turn variety to make setting things much more accurate. sold

 

[Cad602]

PM Sent!

Edit: Asking for the wires, batteries, and the hosts!

cad602

 

[aryntha]

Pontiac,
I'll take the big bag of 9mm diodes; on my phone so I will pm when I get home..

 

[jeffreythe00]

I will take the phr with the driver for 10$! Is that 10$ shipped?

 

[lazeerer]

Ill take the 2x SF-AW diodes.

and the 2 20mW 635nm diodes. Are they the Sanyo ones from DJNY GB.

?

 

[Pontiacg5]

PM Sent!

Edit: Asking for the wires, batteries, and the hosts!

cad602

They're yours, PM sent!

Pontiac,
I'll take the big bag of 9mm diodes; on my phone so I will pm when I get home..

Ok, PM sent!

I will take the phr with the driver for 10$! Is that 10$ shipped?

Yep, $10 shipped!

Ill take the 2x SF-AW diodes.

and the 2 20mW 635nm diodes. Are they the Sanyo ones from DJNY GB.

?

Yep, they were from DJNY's GB. I bought them to build into a few pens but never got around to it. They're yours, PM sent!

 

[mpwn]

did u get my pm?

 

[bobhaha]

Damn... my post didn't go through....

I'll take the 12x diode, all of the 685nm diode (these are TO18 right?) and 2 of the 638nm diodes.

If the buyer falls through, I'll take the hosts and 635nm diodes.

 

[Pontiacg5]

did u get my pm?

Yep, replied to!

Damn... my post didn't go through....

I'll take the 12x diode, all of the 685nm diode (these are TO18 right?) and 2 of the 638nm diodes.

If the buyer falls through, I'll take the hosts and 635nm diodes.

The 685nm were TO-18, I can't remember the recommended current but I believe Cyp or someone had a torture thread for these guys. They're all yours if you want them. The 12x is yours too. I really don't want to split the 638s up though, too many individual envelopes to make it worthwhile.

So far the hosts and 635's are spoken for, I don't forsee either of those being available.

 

[ARG]

If I had 20$ in my paypal, I would buy that disk thing... Does it glow under any wavelength?

 

[bobhaha]

So the 638 is $20 for all of them? If so I'll take them then....

 

[Pontiacg5]

If I had 20$ in my paypal, I would buy that disk thing... Does it glow under any wavelength?

As far as I can tell, yes. It glows better under 532nm than anything higher or lower. 405 is about the edge of where it starts glowing, it's actually really weak in those pictures when compared to 532.

I don't take paypal unfortunately, if you have a paypal debit card I can send a google checkout invoice but I can't do paypal...

Bobhaha, yes that's 20 for all of them.


Edit

I also remembered, I have 10+ A130/140 projectors. I'll sell those individually for $10 each. If you only want a few parts let me know and I'll tear those parts out to save on shipping.

 

[bobhaha]

Done.... Please send PM with payment details.

 

[benmwv]

How much do you think shipping would be for those projectors(Edit: I mean for one, not all of them), and do they still have the red LED in them?