Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

JDS Uniphase 2214-20SLMD laser! (PIC HEAVY)

Re: JDS Uniphase 2214-20SLMD laser on the way!

micheal rosen said:
totally. im also going to have it as part of the rest of my rainbow, so look forward to 900mW of 405nm, 1-2W of 445nm, 20mW of 488nm (might be overwhelmed), 100mW of 532nm, and 900mW of 635nm, all together, all beam enhanced.
Click to expand...

Hopefully your camera sees 488 better than my phone does. 473nm and 488nm look exactly the same to that camera. :(


Here's a link to an album of pictures with my argon and 0.5W 532 labby, surprisingly the 488 isn't over powered *too* badly. Probably doing around 20-25mW of 488 there.

Lasers - Album on Imgur
 





Re: JDS Uniphase 2214-20SLMD laser on the way!

IT HERE, IT'S HERE!!!! WOOOO. haven't turned it on, I have some questions about the PSU though

What can you guys tell me about this:

Also. Is it normal for this cord to be missing a few pins?

 
Last edited:
Re: JDS Uniphase 2214-20SLMD laser on the way!

No interlock key ... huh, sure.

Yes - as far as I remember not all of the pins are used on the round connector - so no need to put pins in all of the slots. Make sure it's in all the way - it'll pop in a few mm then you'll need to twist the ring on the connector to get it to lock in properly. I believe the head interlock is on that connector, so you won't get a green interlock lamp if it's not in.

Make sure you have the HI-LO 220-110 switches adjusted accordingly .

The DB25 connector is for control - pinout is on Sam's FAQ - if I remember correctly you should be able to get it running at idle with just two or three jumper wires between the correct pins. There is another interlock on the controller connector. I'd hook a multimeter up to the current sense pins too (Again, info on the FAQ for the calibration on that), just so you know it's not running at 10A when you think it's running at idle (Usually around 4A for these). If you have a 10k linear potentiometer lying around you should be able to get current control.

Ideally you'd get a blank DB25 male connector and solder your wires/pot/switches onto that and make a proper controller - but you can do without.

Make sure you have plenty of airflow through the head - you need a good 200cfm or so (Think the exact number is on the FAQ) - at 8A tube current this thing will be dumping about 800W of heat. Try not to go up to 10A if you can avoid it - the tubes will do 10A, but they are designed for 8A. Some of the PSUs will actually go up to 11 or 12A.
 
Last edited:
diachi said:
No interlock key ... huh, sure.

The DB25 connector is for control - pinout is on Sam's FAQ - if I remember correctly you should be able to get it running at idle with just two or three jumper wires between the correct pins. There is another interlock on the controller connector. I'd hook a multimeter up to the current sense pins too (Again, info on the FAQ for the calibration on that), just so you know it's not running at 10A when you think it's running at idle (Usually around 4A for these). If you have a 10k linear potentiometer lying around you should be able to get current control too.
Click to expand...

is that key thing just for safety, and they didn't include one?

Anyways, this isn't going to be a plug-and-play thing like I thought it would be huh?
I'll check Sam's laser FAQ but i probably will have more questions, so maybe we should PM about this instead of filling the thread with back and forth talk.
 
Re: JDS Uniphase 2214-20SLMD laser!

Ok, so if I plug it into a wall outlet with a standard PSU cord from xboxes or computers (which seem to fit, surprisingly) it's not going to do anything weird on me if I don't put anything into the DB25 connector?
 
Last edited:
Re: JDS Uniphase 2214-20SLMD laser!

micheal rosen said:
is that key thing just for safety, and they didn't include one?

Anyways, this isn't going to be a plug-and-play thing like I thought it would be huh?
I'll check Sam's laser FAQ but i probably will have more questions, so maybe we should PM about this instead of filling the thread with back and forth talk.
Click to expand...

Yep, it's just for safety really - not sure why there isn't a key switch, but whatever - you don't need it. :D

Edit: Replied to your PM.
 
Last edited:
Re: JDS Uniphase 2214-20SLMD laser!

You need to flip that switch to "HI". Mains voltage is 120V in the US.

The filament will run without the db25 connector, but the tube will remain unlit.
 
Re: JDS Uniphase 2214-20SLMD laser!

Thanks for adding that Cyp! Man, I miss having 230V everywhere. Made consuming copious amounts of power at home much easier.
 
Re: JDS Uniphase 2214-20SLMD laser!

the second i can, ill test run this thing, and see if it works. there is a possibility that it does not function, however i find that unlikely.
 
Re: JDS Uniphase 2214-20SLMD laser!

I think I remember seeing this on eBay the other week, the "208 VOLTS" thing rings a bell.

Anyway, I can't believe I'm just now reading this. Yes, it's completely normal for the connector to be missing a few pins.
IMG_1128_opt_zpsjfnjcbgy.jpg


Also, I haven't actually looked in a while, but I believe you have to jump pins 1 and 3 to bypass the interlock and get it to lase at idle. (someone correct me if I'm wrong)
__________________
\ . . . . . . . . . . . . . /
.\ . . . . . . . . . . . . /
..‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾
1+3 are red

EDIT: Did you buy it tested? If not it could be overpressure or possibly misaligned (although I'd think the latter is much less likely).
 
Last edited:
Re: JDS Uniphase 2214-20SLMD laser!

H2Oxide said:
I think I remember seeing this on eBay the other week, the "208 VOLTS" thing rings a bell.

Anyway, I can't believe I'm just now reading this. Yes, it's completely normal for the connector to be missing a few pins.
IMG_1128_opt_zpsjfnjcbgy.jpg


Also, I haven't actually looked in a while, but I believe you have to jump pins 1 and 3 to bypass the interlock and get it to lase at idle. (someone correct me if I'm wrong)
__________________
\ . . . . . . . . . . . . . /
.\ . . . . . . . . . . . . /
..‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾
1+3 are red
Click to expand...

weird, the pins on mine are backwards to yours... they're listed in the opposite order on the connector.

EDIT: nevermind, i was just being stupid.
 
Last edited:
Re: JDS Uniphase 2214-20SLMD laser!

micheal rosen said:
weird, the pins on mine are backwards to yours... they're listed in the opposite order on the connector.
Click to expand...

I'm gonna go get mine fired up. It needs a run anyway. If you want I'll record the whole procedure and PM it to you.
 
Re: JDS Uniphase 2214-20SLMD laser!

The key switch is missing because that power supply is designed to be integrated into a machine As a component so they chose to omit it probably. If you need to DB-25 blank I have one. Also have the control panel pin out somewhere. These aren't too hard to get running. You can also buy one for Meredith instruments if you're ambitious.
 
Last edited:
Re: JDS Uniphase 2214-20SLMD laser!

Do you have a blower to cool down the laser head yet? Glad to see the PSU will be up and running.
 
You must log in or register to reply here.


Back
Top