Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

GB: 4$ heatsinks, 1.5$ aluminum modules AND more!






AutoItKing said:
so $3 you say? PayPal to mintyfresh?
Click to expand...

the bar comes out to 150g so it costs 4$ actually, now that i cut and weighed it i know ;)
yeah its the same paypal :) please send as goods so i can print the label :thanks:
 
Got the 4$ :)

I'm
Going to cut it now :)


Alright 1/2 done sawing it down :p gotta get a new saw my current one
Is 30 years old & has a pretty dull blade :crackup:
 
Last edited:
AnthoT said:
Got the 4$ :)

I'm
Going to cut it now :)


Alright 1/2 done sawing it down :p gotta get a new saw my current one
Is 30 years old & has a pretty dull blade :crackup:
Click to expand...

Ehhhhhhxcellent.

That sucks! Good thing the blades aren't too expensive.
 
Last edited:
Phew, 45 degrees Celsius (113 farenheight) in my garage & I've only got a tiny bit
More to go :)

Then im off to pack it :)

Darn, also I measured and it came to 5 inches, :p

Done :D

I'm packing it now
Then im buying a new blade :crackup:
 
Last edited:
OK Here is the scoop poop.

The SH GP coppers dont fit the new SH-032/034's They do however fit the old ones Pre-Feb 2012. I had to rip apart my 9mm 445 to find all this out.

Lotsa pics to follow.. flickr is at 86% uploaded..


IMG_4356 by Kizdawg, on Flickr


IMG_4359 by Kizdawg, on Flickr


IMG_4364 by Kizdawg, on Flickr

IMG_4365 by Kizdawg, on Flickr

IMG_4366 by Kizdawg, on Flickr

IMG_4367 by Kizdawg, on Flickr

IMG_4368 by Kizdawg, on Flickr

and here is where it all went awry...


IMG_4368 by Kizdawg, on Flickr

IMG_4369 by Kizdawg, on Flickr

IMG_4370 by Kizdawg, on Flickr


IMG_4371 by Kizdawg, on Flickr OWCH!!!


IMG_4373 by Kizdawg, on Flickr

IMG_4374 by Kizdawg, on Flickr
 
Last edited:
I do have a solution for anyone in my situation. The heatsinks will fit a UniqueFire A10-B (I baught a couple grey ones a couple months back) if we cut about 5mm off the BACK end of the heatsinks.. I am also sure there are other hosts that these will fit I just dont have them all.. lol.. Anyone having problems that finds a solution pls post your finds would be alot easier for us all.
 
Last edited:
Thanks for posting Kizdawg, :)

This problem is both the SH032 & the manufacturer.

I am going to work on getting them remade because I they were machined too large.....

It depends on your host,
If you bought it from DX after February then you may have a problem, if you bought it before them theyres nothing to worry about,

It's about .1-.15 too large so until they get remade then you can sand the side down, 0.1 is not a lot to sand, and you can keep the gold plating on the front where it matters ;)
 
Last edited:
Agreed I would say that DX is mostly to blame. I have found this to be also true on the new WF-501B's I baught where they have remade the hosts and did not make them to the origional specs so my heatsink Euda made was too large and I had to sand it down to make it fit. It sux but I cant blame anyone in particular Well mostly I blame DX.

You did what you thaught was to be right. your measurements were from the origional hosts and there was no way you could know that DX would change there plans for them.
 
Yes, thanks for a the pictures again Kent :)
I'm going to get replacements for all the larger ones.

Can everyone with a SH032 bought AFTER late January please let me know. And please everyone be honest, I already took losses & I will continue too, so don't say you have new ones to just get new heatsinks... Please be honest, then I will replace them for you :)
 
AnthoT said:
Yes, thanks for a the pictures again Kent :)
I'm going to get replacements for all the larger ones.

Can everyone with a SH032 bought AFTER late January please let me know. And please everyone be honest, I already took losses & I will continue too, so don't say you have new ones to just get new heatsinks... Please be honest, then I will replace them for you :)
Click to expand...

Hey, i bought SH032's two months ago. So they dont fit? I can compensate you for correct ones if you want?
 
offroadfreak8582 said:
Hey, i bought SH032's two months ago. So they dont fit? I can compensate you for correct ones if you want?
Click to expand...

Can't say for sure....

If anyone wants to help out then just paying shipping to you is great, it would help me a lot...

But whoever has them can also sand them a bit, 0.1mm is not that much, it's probably like 5 - 10 minutes At most and you can keep the front gold plated then it would fit, but that would be a temporary solution, until the new ones get here.
 
Last edited:
Can I wait until mine comes so I can test it because I bought the host from Jayrob so I'm not sure when it was purchased.
 
You must log in or register to reply here.





Back
Top