Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

FS: ***MXDL Custom Machined Heatsinks***

Jay, I dont have any 80 grit sand paper to do the insides so my freak module will fit. Would 60 grit be okay? I mean, obviously 80grit is better but would 60 grit do the job?

+1 rep, too
 





Thanks for the rep guys!

el-taco, yes 60 grit would be fine. It shouldn't need much... Probably just some sanding around the set screw area. The aluminum gets a little 'pushed out' when the drill bit punches through.
Jay
 
el-taco said:
My module is a tad too fat...
Click to expand...


Hmmm.... this is the first I have heard of this. I use the same drill bit. I have heard (and experienced) that sometimes the module will start to slide in, but stop at the set screw area.

Are you using a module from AixiZ?
Jay
 
jayrob said:
[quote author=el-taco link=1202452073/400#419 date=1219579811]
My module is a tad too fat...
Click to expand...
Hmmm.... this is the first I have heard of this. I use the same drill bit. I have heard (and experienced) that sometimes the module will start to slide in, but stop at the set screw area.
Are you using a module from AixiZ?
Jay[/quote]

AixiZ = .466 in. (11.85mm)
Sure = .472 (11.99mm)
I don't have a DX module here

Peace,
dave
 
Good information Dave! Thanks...

That's it then. The heatsinks are fit for AixiZ (or DX) module. I have tried the DX, and they are the same size as the AixiZ. The Sure module is too big...
Jay
 
I bought it from TheMonk, he said it was an Aixiz module. Im fairly sure it is, Im not too sure what a Sure module looks like though.
 
I use the same drill bit to bore out the center, so the size of the hole is exact. If the module does not even start to slide into the heatsink, then it is either a freak AixiZ module, or it is not an AixiZ module. It's a good thing that AixiZ modules are cheap! You can get one at Stonetek.org, or if you want a 10 pack, AixiZ sells them on e-bay...




Spyderz20x6, your sku 46 heatsink and o-ring will be in tomorrow's mail! (Monday)
Jay
 
climbak, just to let you know that since I got your heatsinks done, I'll be dropping them at the Post Office today (Tuesday), instead of tomorrow...
Jay
 
jayrob said:
I use the same drill bit to bore out the center, so the size of the hole is exact. If the module does not even start to slide into the heatsink, then it is either a freak AixiZ module, or it is not an AixiZ module. It's a good thing that AixiZ modules are cheap! You can get one at Stonetek.org, or if you want a 10 pack, AixiZ sells them on e-bay...




Spyderz20x6, your sku 46 heatsink and o-ring will be in tomorrow's mail! (Monday)
Jay
Click to expand...

I bought a diode pre installed in the module. Im going to give the ol' sandpaper a go in a while, Ill report back.
 
JaxSmirkingRevenge, your heatsink will be in tomorrow's mail. (Tuesday)




thesk8nmidget, yours too! And your piece of mirror...
Jay
 
LRMNmeyer, your sku 46 heatsink and o-ring will be in Monday's mail...
Jay
 
You must log in or register to reply here.


Back
Top