Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

FlexDrive v5 worries... how do i test load this thing and not fry my diode?!

Kaokin

Kaokin

0
Joined
Oct 31, 2009
Messages
31
Points
0
I just ordered a PHR sled to practice on and a GGW sled for my final build as well as a FlexDrive v5 as my driver. I have been reading quite a bit and i know that it is strongly recommended that you test load the driver and measure the current before mounting the diode, but i cant seem to find any detailed information on how to do so... I have a DMM but i dont have very much electronics knowledge... Do i need to build a test load or can i just short the output terminals or use a resistor or ??? :thinking: Any help is appreciated!!!
 





Last edited:
This is probably the most asked question on this fine forum, and just short of plagiarizing any response you will find your answer I'm sure if you try using the search
feature. It's there I know.
 
Jayrob, Thank you very much, that explained driver circuits and test loads nicely :yh: I will go to radio shack today and see if they have the diodes. The only other thing i am alittle unclear about is the forward voltage produced by the flex drive. I have read the flexdrive PDF manual and understand the soldering jumpers and pot for setting the current, but how is the forward voltage set?



Jander: i used the search feature and looked for well over an hour before i asked this question, which i indicated in my post. Just because i am new here and only have 2 posts please dont assume i am some kind of idiot who doesnt know how to use the search feature. Jayrob answered my question quicky and concisely in 30 seconds flat.


Thanks for the help jayrob :beer:
 
Why don't you try out one of my easy to use PYRO Test Loads here is a picture.
igzyig.jpg

you will find them in the laser pro shop along with other fine laser tools you my need to get the job done !

Peace All FlaminPyro...



Kaokin said:
I just ordered a PHR sled to practice on and a GGW sled for my final build as well as a FlexDrive v5 as my driver. I have been reading quite a bit and i know that it is strongly recommended that you test load the driver and measure the current before mounting the diode, but i cant seem to find any detailed information on how to do so... I have a DMM but i dont have very much electronics knowledge... Do i need to build a test load or can i just short the output terminals or use a resistor or ??? :thinking: Any help is appreciated!!!
Click to expand...
 
Kaokin said:
I just ordered a PHR sled to practice on and a GGW sled for my final build as well as a FlexDrive v5 as my driver. I have been reading quite a bit and i know that it is strongly recommended that you test load the driver and measure the current before mounting the diode, but i cant seem to find any detailed information on how to do so... I have a DMM but i dont have very much electronics knowledge... Do i need to build a test load or can i just short the output terminals or use a resistor or ??? :thinking: Any help is appreciated!!!
Click to expand...

After 1 hour on the search and you can't find any detailed info on
this...:undecided: also, I'm not in any way calling you an idiot nor have I ever to any forum member, sir.

I know that questions beget questions and in short could be found in the search.

Myself... I lurked here for over a month before asking this same question
that you just did only becouse I was less inclined to be spoooned feed.

I want to start over again and just say welcome :beer:any questions use the search.

Just be glad forum member Tech_Junkie wasn't repling cause he would have been less ginger in his responces, especially when it comes to new members asking the ol' test load questions.

PS. don't forget to short the caps. peace JOsh.
 
Thanks Josh, im no trying to be spoon fed either i just have a bunch of components on my workbench and im excited to get started, thats all, im sure you can relate to that!

Flamingpyro, i noticed those test loads in another thread, very sweet!!! i was actually contemplating getting one and some of the silicone wire from you as well as a few other misc things... What i really need is a heatsink or two; and i noticed that really sweet lathe setup you have there ;) I know you have done alot of work on alot of different hosts, have you ever made a heatsink for a Trustfire Tr-801? would you be willing to make an easy custom heatsink for an uncommon host if i gave you dimensions?? I am using a 405-g-1 lense mounted in a 10.5mm housing as shown here:
 
Kaokin said:
Jayrob, Thank you very much, that explained driver circuits and test loads nicely :yh: I will go to radio shack today and see if they have the diodes. The only other thing i am alittle unclear about is the forward voltage produced by the flex drive. I have read the flexdrive PDF manual and understand the soldering jumpers and pot for setting the current, but how is the forward voltage set?

Thanks for the help jayrob :beer:
Click to expand...

You don't have to worry about voltage. (for normal diodes up to 6X blu-ray's - V5 will give at least 300mA's up to 6 volts demand) The FlexDrive is designed to regulate the current with the voltage demand being taken care of.

All you need to do, is have the proper supply (between 2 and 5.5 volts), and have the current set properly. And the diode will take what ever voltage it needs.

3 X AAA batteries (standard or rechargeable), 2 X AAA (or other 1.5 volt batteries), a single lithium battery (primary or rechargeable), are all perfect supplies for a FlexDrive red or blu-ray...
 
Last edited:
Im at the point where I need to solder a jumper across 3 resistors to set the flexdrive v5 to 155mA~600mA
These drives are allot smaller than expected & thought Id best ask one of you for any useful advise at this point as not to screw up.

I thought of using a pin as the jumper, but appears too big, now im wondering if tinning a single strand of copper wire to bridge the resistors would be a better option,
Any suggestions?
 
netwave said:
Im at the point where I need to solder a jumper across 3 resistors to set the flexdrive v5 to 155mA~600mA
These drives are allot smaller than expected & thought Id best ask one of you for any useful advise at this point as not to screw up.

I thought of using a pin as the jumper, but appears too big, now im wondering if tinning a single strand of copper wire to bridge the resistors would be a better option,
Any suggestions?
Click to expand...

Watch this video thanks to mohrenberg.

http://laserpointerforums.com/f51/how-set-flex-drives-current-45653.html
 
excellent tutorial thanks..
had a chuckle when I saw the nail clippers come into the scene for snips, as I too thief the house hold clippers for the same purpose
 
netwave said:
excellent tutorial thanks..
had a chuckle when I saw the nail clippers come into the scene for snips, as I too thief the house hold clippers for the same purpose
Click to expand...

I think we all do haha.
 
You must log in or register to reply here.


Back
Top