Kenom
0
- Joined
- May 4, 2007
- Messages
- 5,628
- Points
- 63
Little bit pissed off at ebay's newest attempt at trying to make the masses happy. I recently sold a laser diode on ebay in a aixiz module. Jackass decided to do the kipkay hack and what do you suppose happens?? He fries the damn thing. Ok fine. one would think lesson learned. BUT NOOOO! he comes back on me saying I sold him a defective laser. Leaves me negative feedback because I tell him that the kipkay hack will kill a diode instantly and I'm not going to be responsible for replacing something that came to him functional. EVEN HE SAID IT WAS WORKING WHEN HE GOT IT!!! I'll post the emails I got from this moron.
Dear kenom,
ok...... im makeing a flashlight hack
There are 3 pins on the diode. one positive, one negative, and one photodiode. The diode came from sony.
yes... i work with lasers.... but this would be my 1st time.. makeing my own dvd writer laser.. so well see how it turns it out..
I recommend looking at Laserpointerforums.com for any help you need.
has it been shipped yet?
it was shipped on monday. You should have it in your hands by now. Hopefully.
alright.... i dont mean to seem like a jerk but this laser is fualty.... i had it 2 aa battarys and i measured 179mw on my meter at work...see here he says it worked but these are supposed to get 2000+ hours and this one only had less than one..... its dead and i put it in multiple casings (minmags) and changed the battarys many times ... now if there is anything you can do please contact me... I think the diode ran out but i do not want to drill it intill you see it..... Now i do not want to leave any feedback intill this is over with... if you would like me to send it back to you just tell me.... Thank you
You drove it unregulated? that is why it's dead. I clearly indicate in teh auction that current regulation in NECESSARY. unlike what kipkay says you CANNOT run your laser off 2 AA's without blowing it up. I can't warrant you treating the diode like it was NOT intended to run. Nor did I indicate I would on the auction.
I know... i had a 2mm pot above it so i had to drill out the glass.. i can send you a picture of all of it if you would like... like i sait i work with lasers from (Lasic vision) I inspect the 300p machines .. so i knew what i was doing..
I don't want you to think I'm indifferent to your plight. But, I do want you to read over this page.
http://www.laserpointerforums.com/forums/YaBB.pl?num=1210343867/0#0
You'll notice it's not just me that claims to not using a laser diode straight off batteries.
No this is what you said....
Up for auction today is a >200mw laser diode installed in a module.
No driver is included you must provide.
laser diode is capable of producing 200mw of 660nm energy.
3v @ 200-400ma
Each unit is tested before shipping and shipped FAST.
good for incorporation into your own product.
3v @ 200-400ma
Each unit is tested before shipping and shipped FAST.
No driver is included you must provide.
Just beacuse i used a mini mag flashlight dont mean that i copyied kipkay... In the lasic 300 the machine uses a 16mm P.O.T. so i know how these things are installed
Well, as you indicated. The laser WAS functional when you recieved it. I cannot be responsible for it after you recieve said working diode.
ok... its your feedback.. i can just make a new account it dont bother me.. ok?? Nice doin business with you...
yes but the laser was a peice of shit..
sorry you feel that way. I'm made hundreds of 200mw lasers from these very diodes. Using a "p.o.t." as you inexpertly refer to them gives me an indication of the experience you DON'T have when assembling lasers.
OK my rant is, that now that ebay has changed the feedback system so that I cannot leave negative feedback towards this jackass, I'm literally left with no recourse in alerting other sellers and buyers that this jerk is a crybaby when he doesn't follow simple directions.
What do you think? I think they should only allow negative feedback towards a seller when a dispute is won against the seller on paypal. Paypal you actually have to take the time to build your case. Unlike egay which doesn't care. Now I have an unwarranted negative feedback. stupid f*(*&kin ............... /rant
Dear kenom,
ok...... im makeing a flashlight hack
There are 3 pins on the diode. one positive, one negative, and one photodiode. The diode came from sony.
yes... i work with lasers.... but this would be my 1st time.. makeing my own dvd writer laser.. so well see how it turns it out..
I recommend looking at Laserpointerforums.com for any help you need.
has it been shipped yet?
it was shipped on monday. You should have it in your hands by now. Hopefully.
alright.... i dont mean to seem like a jerk but this laser is fualty.... i had it 2 aa battarys and i measured 179mw on my meter at work...see here he says it worked but these are supposed to get 2000+ hours and this one only had less than one..... its dead and i put it in multiple casings (minmags) and changed the battarys many times ... now if there is anything you can do please contact me... I think the diode ran out but i do not want to drill it intill you see it..... Now i do not want to leave any feedback intill this is over with... if you would like me to send it back to you just tell me.... Thank you
You drove it unregulated? that is why it's dead. I clearly indicate in teh auction that current regulation in NECESSARY. unlike what kipkay says you CANNOT run your laser off 2 AA's without blowing it up. I can't warrant you treating the diode like it was NOT intended to run. Nor did I indicate I would on the auction.
I know... i had a 2mm pot above it so i had to drill out the glass.. i can send you a picture of all of it if you would like... like i sait i work with lasers from (Lasic vision) I inspect the 300p machines .. so i knew what i was doing..
I don't want you to think I'm indifferent to your plight. But, I do want you to read over this page.
http://www.laserpointerforums.com/forums/YaBB.pl?num=1210343867/0#0
You'll notice it's not just me that claims to not using a laser diode straight off batteries.
No this is what you said....
Up for auction today is a >200mw laser diode installed in a module.
No driver is included you must provide.
laser diode is capable of producing 200mw of 660nm energy.
3v @ 200-400ma
Each unit is tested before shipping and shipped FAST.
good for incorporation into your own product.
3v @ 200-400ma
Each unit is tested before shipping and shipped FAST.
No driver is included you must provide.
Just beacuse i used a mini mag flashlight dont mean that i copyied kipkay... In the lasic 300 the machine uses a 16mm P.O.T. so i know how these things are installed
Well, as you indicated. The laser WAS functional when you recieved it. I cannot be responsible for it after you recieve said working diode.
ok... its your feedback.. i can just make a new account it dont bother me.. ok?? Nice doin business with you...
yes but the laser was a peice of shit..
sorry you feel that way. I'm made hundreds of 200mw lasers from these very diodes. Using a "p.o.t." as you inexpertly refer to them gives me an indication of the experience you DON'T have when assembling lasers.
OK my rant is, that now that ebay has changed the feedback system so that I cannot leave negative feedback towards this jackass, I'm literally left with no recourse in alerting other sellers and buyers that this jerk is a crybaby when he doesn't follow simple directions.
What do you think? I think they should only allow negative feedback towards a seller when a dispute is won against the seller on paypal. Paypal you actually have to take the time to build your case. Unlike egay which doesn't care. Now I have an unwarranted negative feedback. stupid f*(*&kin ............... /rant