Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

Blu-ray labby (lots of nice pics)

50% of the sockets in my house aren't even grounded. :-X


I will try to insulate the heatsink tho, and if something happens with the diode I'll let ya'll know.
 





Hehe, yeah, i have a few such sockets too - using the mass as ground.. By itself it works, but if you connect two devices between each other, and one is in a grounded socket and the other one in the tweaked socket, you short the electrical system and burn a fuse.. ;)

But i don't think the socket has to be grounded to provide a discharge path...
 
Nice work FML! Like everybody else I like how you soldered those washers together to make a heatsink.
 
WHAT?! that sounds deadly! :o


I have to ask you something while you're at it.

I made a centrifugal water pump out of a big 24v DC motor, powered by the 12V adapter in the pic above. When I was done I wanted to test is so I filled up the kitchen sink and turned it on. My elbows rested on the sink, the motor drive shaft is exposed to the water and the motor's casing is made of metal, which I held in. I dipped the pump in the water and it worked (of course [smiley=happy.gif]). At first I didn't feel anything, but after a short while my elbows got kinda hot, later painful. Then stinging.

Why is that? :-/

styropyro said:
Nice work FML! Like everybody else I like how you soldered those washers together to make a heatsink.
Click to expand...
Thank you. :)
 
FireMyLaser said:
WHAT?! that sounds deadly! :o
Click to expand...

Actually no. It would be "deadly", if it was connected to phase. But this way, it is safer than no ground.


FireMyLaser said:
My elbows rested on the sink, the motor drive shaft is exposed to the water and the motor's casing is made of metal, which I held in. I dipped the pump in the water and it worked (of course [smiley=happy.gif]). At first I didn't feel anything, but after a short while my elbows got kinda hot, later painful. Then stinging.

Why is that? :-/
Click to expand...

;D I don't think it has anything to do with electricity.. Especially since you powered it from only 12V...

I think it's more likelly to be related to you resisting the centrifugal forces and leaning on the sink too hard?
 
No the pump isn't constructed like that. I tell you - it hurt! It felt like electricity. I haven't used the thing since...


I have a multimeter, but oh the irony: the battery is dead now.
 
silly question, but where did you wire your controll led? before driver,parallel to ld(i know silly guess) ??
Thanks, ArRaY
 
ArRaY said:
silly question, but where did you wire your controll led? before driver,parallel to ld(i know silly guess) ??
Thanks, ArRaY
Click to expand...
Probably with a different driver, if he ran it parallel with the LD it would suck away some of the LD's power.
 
It's not a silly question. I put a 1Kohm (1000ohm) resistor in series with the LED and connected that across the power cable in to the box. So it's before the driver. The LED can then run on 4-16V. The current thru the LED changes with the voltage, which can mess up the the reading of how many mA the laser get. So the best thing to do is to use a stabilised power supply and measure the current thru the LED at in this case 9V. Let's say that it is 10mA. Then connect the laser and driver and you want let's say 100mA, turn the pot to 110mA. 110 - 10 = 100mA.

Or you set the current to whatever you want to the laser and then add the LED.

Or use a 1 ohm resistor in series with the laser diode and measure the mA with volts.
 
You must log in or register to reply here.


Back
Top