Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

An Even Brighter Key Chain Flashlight Mod!

Kenom said:
They are "obsolete" says the company. Donno how a micro micro latching switch can be obsolete in a world of smaller and smaller.
Click to expand...


I just got off the phone with the lady at E-switch and she had me e-mail her my mailing address...

She said she will get me 6 of them by March.
Jay
 





I'm pretty sure this mod is complete minus the clicky. You can't improve on perfection!
 
Ha ha! Thanks for that compliment Ken! :)

As far as it being complete, I know that I am done with it! ;D

I'm not sure there will be a better switch than the 'push on - push off' clicky that I have already put into 3 of these. But we can still try when I get some of those ones from E-Switch.

Looking back, even though the time and effort to fit the larger 12mm X 12mm clicky with the 3 ohm resistor was a pain, it is a very solid build. And now with my glass lens and aluminum reflector mod, it is REALLY nice! (for it's size) Drawing about 332mA with a fresh charged 10280! And will last as well! 8-) (those E-Switches are only rated for 100mA's, but they will surely take more)
Jay

P.S. I put the reflector mod on my 1st one now too. The one that is using the stock circuit and drawing about 120mA's. With the reflector, it is much brighter. Maybe even a better way to go because it will have about a 2 hr. run time per charge with the 10280!

MCBL20.jpg
 
This is the most awesomestest builds around. I mean keeping a Cree light on your Keychain?!?! How awesome is that?!@?!
 
here is the switch I'm referring to compared to the one your using.

DSC00402.jpg
 
That would easily fit in there Ken! :)

I guess the hope of finding a latching switch that would be small enough to use the stock board that slides into the center of the host is probably not possible. That would have been an easy mod with a switch that small...

For sure that switch you show can work. With plenty of room on one side to put a resistor. The problem will become to mount it solid inside the host.

The large switch that I have used had to be sanded and shaved in order to be able to fit! So it is a solid mount inside the host. I don't know if the build is going to be harder or easier with smaller latching switches! :-/  But we shall soon find out...
Jay

P.S. Maybe I can utilize the stock board by cutting a slot in the center for the switch to fit into, then it would be able to stabilize the switch where we need it to be!
 
here is another picture.  I've modified the switch just a teenie bit and put the cap on top.

DSC00403.jpg


I donno bout the original pcb but I've no doubt we could make one work. The board this one came off of is incredibly thin and had a resistor mounted right next to it.
 
I'm thinking that we could cut a square fit for that switch, out of the center of the stock board...

Right where we need it to be positioned. Remove the stock components and fit that switch with a 3 ohm resistor!
Jay

MCBL2.jpg
 
Another cool mod for this great Key Chain host! :)

This time it is using a huge, super bright 'Blue' LED with a very narrow beam (10 degree), and a 10280 battery...

MCBlue1.jpg

MCBlue2.jpg

MCBlue3.jpg


The wall in the beam shot is 30' away! This sucker is so bright that it just about has a beam at night! If the beam was any narrower, it would be a 473nm laser! :D
Jay
 
You must log in or register to reply here.


Back
Top