A host that uses 26650 batteries ?

[Accutronitis]

does anyone make a laser host that uses 26650 batteries ?

 

[Crazlaser]

You should PM a few of the machinists, for example electricplasma, maybe lifetime.

 

[Deleted member 42751]

ASP hilts from SaberForge can be used with 26650 batteries, but lightsaber builds are a notch above your typical builds, in both cost and difficulty. So if I were you I'd ask one of the LPF machinists first as Crazlaser recommended.

 

[Lifetime17]

Hi Acc,
I have 26650 modded hosts with Aluminum or Copper heat sinks that i make in a plug n play just drop in your 12mm module and drive and lens , your good to go.

Rich

 

[Accutronitis]

Hi Acc,
I have 26650 modded hosts with Aluminum or Copper heat sinks that i make in a plug n play just drop in your 12mm module and drive and lens , your good to go.

Rich

Can it work with one of DTR's 6W NUBM44 450nm 25mm Copper Laser Module W/Blackbuck Laser Driver ?

 

[Chrisbee]

That'll most likely be for a 12mm module. But it's still a big chunk of copper either way. If you didn't use the copper pill that's already in that MX900 host, you can make one of the 25mm ones work. Although I don't know how much modification that'd require.

 

[Deleted member 46822]

I was going to say Maglite's with the C cells, but Lifetime's build is as good as it gets to plug an play with just the 12mm module swap.
If you already have DTR's 25mm module just hold on to it as you will sure use it soon..

 

[Lifetime17]

Hi
As said you won't need that 25mm sink with my hosts. The sink I make
With the XM900 or the Mag light are more mass than the 25. But that's up to you. DTR has some awesome stuff

 

[Accutronitis]

Hi
As said you won't need that 25mm sink with my hosts. The sink I make
With the XM900 or the Mag light are more mass than the 25. But that's up to you. DTR has some awesome stuff

How do you focus the beam ?

 

[Lifetime17]

Hi
The lens
Screws
Into the 12mm module and
Then a focus knob screws
Onto the lens . Now you solder two wire and heat shrink tubing.!now slide the 12mm module into the heat sink and tighten the set screw. Done
The search at will help you also for nfo

 

[Accutronitis]

Dang it, I have to finish my green monster host build that is ready to have one of DTR's 6W NUBM44 450nm 25mm Copper Laser Module W/Blackbuck Laser Driver pressed into it but I don't have the 2 x 22650 batteries I need for it BUT I have a bad a$$ set of IMR 26650 60 Amp max pulse current 4500mAh batteries that are just dying to power something !

 

[Lifetime17]

Hi,
The XM900 host that i sell with heat sink and focus knob take 2-26650 batteries and it comes with a plastic sleeve to reduce the inside diameter on the battery tube to take 2-18560's as well. I can machine a sink and knob in Aluminum or copper . copper will be a little higher because of the cost of material and labor. I posted a ic of the one in copper but you can also choose Aluminum to ..it will come prewired so all you do is add your driver and diode and lens.

rich

 

[Accutronitis]

Hi,
The XM900 host that i sell with heat sink and focus knob take 2-26650 batteries and it comes with a plastic sleeve to reduce the inside diameter on the battery tube to take 2-18560's as well. I can machine a sink and knob in Aluminum or copper . copper will be a little higher because of the cost of material and labor. I posted a ic of the one in copper but you can also choose Aluminum to ..it will come prewired so all you do is add your driver and diode and lens.

rich

Well I def have to add a over 1 watt green laser to my laser collection I've started, So after I finish the DTR 6W NUBM44 450nm 25mm Copper Laser Module / green monster host the next one up will be one of your XM900 hosts so I can use my IMR 26650 batteries....

 

[Lifetime17]

hi,
Sound good buddy.
Rich

 

[RedCowboy]

I use the MX-900 when you can find them, they have a nice springboard that you can repurpose, or you can toss it and make your own and get 3 x 26650's into the mx-900 without searching for the hard to find extensions.

---Both hold 3 x 26650's----