Search results

Thanks! :)

I did try that, it didn't do much though. The 7414 has too wide a hysteresis band(it did work for some people though) so the newer drivers use a comparator. Hmm... :thinking:

Thanks! I am using Steve's UD 1.3b. Unfortunately, without phase lead I am switching about 70 degrees too late! Nasty spikes on the bridge output!

Hi guys! Here is my DRSSTC. CM600 full bridge. Slightly modified UD 1.3b. Photos are 340V on the bridge, around 500A primary current, 240bps and 190us on time. It makes 4-5 feet of spark until I redo my bus cap configuration. Thanks for looking!

Here are some of my coils. Fullbridge PLL SSTC. Half wave rectified mains. Same coil only using antenna feedback into a buffer. Fullwave rectified 240 from a step up transformer. Driver is Sigurthr's USSTCC! Thanks Sig! Class E PLL SSTC. Filtered mains in this picture. Resonant...

It was finished last year. The build was also finished however one of the driver's ICs popped off and I procrastinated on buying a new driver and got sidetracked by other projects. I will see if I can get it up and running next weekend when I have time. Thanks for the interest! :)

To help with the mot's leakage inductance and saturation issues a good amount would be to wind at least 20 extra turns on the primary. This would allow you to remove those shunts. I heard it brings the magnetizing current to under 500 ma for adding 30 extra turns. This will also increase your...

Ah yes. You mentioned that to me earlier. My memory failed me there. ;) Any trustworthy smps companies that you know of? They are cheaper and the frequency makes them a bit easier to use for some purposes.

That's a really lucky ebay find! For the smps, yes, the load determine the draw. I think tha it is the resistance(or impedance if you don't rectify it) of the plasma that determines the current. I had one on hand from an old neon sign. I used it to power a discharge tube with 22 ma optimal...

Is it an old one or a small switched mode psu? I had trouble before with my smps as it said 30 ma but actually measured around 3.

He needs fast diodes. Those are for 60hz. I think they might make switched mode ones nowadays though but those are hard to find.

You can find them online. RadioShack won't have those diodes

Get diode's rated for your voltage and double that, and find ones that say that they are fast. Make a rectifier. There are plenty of instructions for it online.

Caps don't make noise in curcuit when discharging AFAIK. The crack is the quick breakdown of the air when you discharge it manually. But in your case the popping you hear when it's running is the spark gap which is the same thing as above just the gap is positioned so that it breaks down for...

Idk about winding a transformer as you need an iron core and I wouldn't know how to set that up. 60hz is standard for neon sign transformers. 16000 hz is too high because your capacitors do not react well with that frequency. The dielectric is glass which high frequency passes through...

USAbro your problem isn't your power, it the the frequency you are using. Unless you get or make an rf cap, you can put as much power into the coil as you want but all that will happen as already stated is you will loose a ton of power. Easy answer, talk to your local neon sign guy and see if...

It's fake.

As I said, he didn't use a flyback it was an nst. It also wasn't my coil but a friend's.

USAbro everything you wound is fine. You just need to fix the tank cap and rewind the flyback. Step one: do the equation I already gave you and give yourself at least 4 kv LOSSES INCLUDED Next wind thin wire for the secondary. Make sure you keep track of the way it is going and turns. So...

Wind a lot of turns. You need to minimize loss and prevent core saturation. Vin/Vout=Primary turns:secondary turns. Be sure to add more because you will have loss.