Just a follow up from my comments on this thread - I've been in touch with Lifetime17 exchanging PMs and details. I am thankful for his knowledge & time with orders like mine and I dont want to leave an impression here that nothings happening since I've posted. Not the case at all, we're busy...
Nice, looks like you could definitely do what Im looking for! I sent you a PM on Monday about a cpl of hosts from your sales thread after you posted but haven't heard back. We're all busy, no complaining from here but Im interested in communication & reliability. Does anyone know of other LPF...
old thread reboot!
I also need a 25mm host to hold one of DTRs copper sinks. If anyone can link me to any thread(s) that I'll be searching later on when time allows, I'll smile at you all day. If not it's cool, Im reading so far that 25mm isn't the most popular sink for handhelds obviously bc...
Hello, Welcome!
First off dont be discouraged if you're not responded to on this thread for a couple days from time to time. This thread isn't very active but for many of us into Lumia as much as you sound to be, I'm very interested to see what kind of information or ideas you get regarding...
I have a cheapy RGB projector (green burnt out, using a separate module mounted above RGB) shining through a translucent lightbulb on a very slow rotating motor. All 3 beams are constanst, solid lines - no patterns
:beer:
Thanks!
Yes I'm big on the slow motors compared to the faster ones I have Jerry, using a 4RPH motor in this one and I find this speed & similar RPH ideal because you can really concentrate & appreciate more detail before whatever you're seeing morphs into something else ;)
:beer:
Greetings LPF!
I recently rebuilt my home studio after a few years of hibernation & being busy for too long. Upon finishing this I decided to incorporate my old lumia setup (thanks hakzaw!!) to project where I was going to put some influential artwork.
I thought of sharing a snippet of what...
I apologize, still out of stock on these units but my distributor contacted me last week & supposedly has new stock. I am going to order a sample & if it's the same unit as before then YES - you can buy a polished chrome w/ a heatsink.
I'll follow up once I know if this is identical to what I'd...
If you dont mind I'll share this here in case someone else has similar problems or questions with these drivers, pictures often help ;)
The joint I made is just to the left of LD-
Indeed and yes it's adjustable. I can set it anywhere between 100mA & ~600mA which is its range in low power...
Thanks for your feedback, that seems to be the case with the driver being made for just one cell because it's a mini boost driver and I missed this previously reading up on these
X-Boost V7 input voltage range is 2.5 to 9.0 volts
X-Drive V6 input voltage range is 3.4 to 16.0 volts
SXB-2 all...
Ah thanks for the explanation ;)
My PS is dead unfortunately, I can't test with it until I replace mine.. I have tried different batteries though to rule out bad cells but that same thing happens.
Im also assuming this driver can handle 2 x 3.7Vin, Im not positive & haven't found specs on this...
Greetings!
I've had a couple of these S-mini drivers from Pyro dating back months ago & recently used one of them in a build I've started. After soldering everything up I successfully tested the driver in low power mode, then soldered those 2 tiny resistors for high power mode - also...
Is there a battery contact spring inside the tailcap you can stretch & lengthen a little by pulling on the tip of the spring with a pair of tweezers? Have you also tried a small spacer between the cells?
I've had a few lasers that either needed longer cells for a tighter internal connection to...
I dont think its concerning but Im not surprised because these diodes aren't necessarily installed for extraction. I've never seen something like that as a bullet under 'features' before. Clearly proves we've been noticed yes, lets just hope it's not an irreversible feature from removal ;)
:beer:
This was a good read, great find thanks for sharing Garoq!!! While I'm impressed I'm also a little disappointed, they didn't answer one question that is undoubtedly on everyone's mind.......
can it pop balloons??
:beer: