Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

what color laser burns the best?

Bogdan

New member
Joined
Oct 15, 2018
Messages
2
Points
1
green, blue, red or violet?

q2: if you have 2 100mw lasers (one green one red) and the red one burns better but the green one is more visible, would you go blind faster from the green or red laser?
 





Joined
Sep 4, 2018
Messages
562
Points
63
Before I answer - whatever you do, get laser safety glasses appropriate for what you are thinking of getting.

Your first question is fairly simple, though double edged - There's not a lot of difference between colours in actual burning capability, but there is a huge difference between what is powerful and available at different colours (wavelengths).

For example, 445nm (blue) lasers are readily avaliable and can output a lot of power (1-7W), you won't find a green diode that can output more than 1W. Much more important for burning is focus - i.e. even a relatively low-power laser (e.g. 100mw) can burn some materials if focused to a narrow point.

Your second question on the other hand slightly worries me. Never use powerful lasers (class 2 or higher, i.e.) indoors without proper laser safey glasses. You should not entertain the fact of going blind - 100mw of Red and 100mw of Green will cause the same damage to a retina (unless the green is an IR unfiltered 532nm, in which case there is likely much more power being output in the invisible part of the spectrum)
 
Joined
Sep 20, 2013
Messages
17,253
Points
113
As far as burning things with a laser the color of the material to be burned is also a factor. Black objects absorb more of the beam's power than light colors or white. If you are using a red laser, you don't want to try to burn a red material as it will reflect more light than it will absorb.

Power density of your beam is also an issue here. Single mode diodes like the S06J and the BDR-209, 405nm lasers, have higher power densities than many higher power multi mode diodes do.

The wording of your last question is cause for concern. It sounds like you are looking for the laser that will blind the best. Always take laser safety very seriously. It is the power density of the beam, not the color that will cause the worst retina burns. Color doesn't matter at all. Get the appropriate laser eye wear for the laser you intend to buy.
 

Encap

0
Joined
May 14, 2011
Messages
6,112
Points
113
green, blue, red or violet?

q2: if you have 2 100mw lasers (one green one red) and the red one burns better but the green one is more visible, would you go blind faster from the green or red laser?

A laser beam has no temperature - there is no inherent "temperature" to a laser beam.
Heat is the random motion of matter particles (atomic or molecular particles).
A laser beam itself is not made of matter but of photons, which have no mass, thus a laser beam can have no temperature.
"Heat" is caused by a laser beams energy being absorbed by a materials surface and turning light energy into heat energy.
"Burning": depends upon the ability of the target to absorb and convert the light energy of whatever wavelength to heat.

If you want to know about laser eye hazards--have a look at this good chart: http://www.lasersafetyfacts.com/resources/FAA---visible-laser-hazard-calcs-for-LSF-v02.png
 
Last edited:

CurtisOliver

0
LPF Site Supporter
Joined
Jun 12, 2015
Messages
7,594
Points
113
As others have already stated. Its not the 'colour' that is better at burning. Wavelength is somewhat important, but only due to the materials absorption. As Encap has stated well, lasers do not carry thermal energy. Instead it goes on several factors. Power density, being a big one.
 

Coonie

0
Joined
Jan 12, 2018
Messages
303
Points
43
405nm is your best but for raw power 445 is your best choice. As others have said, be careful. You should consider these lasers as weapons because you will blind someone. It's not a maybe but 100 percent certainty that you will blind yourself or someone if hit in the eye. Remember it's a loaded gun.
 

Benm

0
Joined
Aug 16, 2007
Messages
7,896
Points
113
I'd agree that the shorter wavelengths have the most burning potential, even fluorescence causes heating of the target and potentially setting it on fire. If you want to focus your beam down to a small spot to get the maximum power density possible a single mode diode would be the best choice, which results in 405 nm.

You can get a lot more raw power from multimode diodes like the 445's though, so it would depend on what you actually would like to burn with your laser.
 




Top