FokoF
0
- Joined
- Jun 24, 2007
- Messages
- 508
- Points
- 0
http://www.photonlexicon.com/forums/showthread.php?t=6475 analog driver, just though it might be relevant.... Good luck!
Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers
Buy Site Supporter Role (remove some ads) | LPF Donations
Links below open in new window
FrozenGate by Avery
TTL laser diode driver
- Thread starter b52productions
- Start date
diachi
0
- Joined
- Feb 22, 2008
- Messages
- 9,700
- Points
- 113
Both of these drivers use the same IC ( LM358N ) which is the 8 pin chip.
Regards,
Adam
EDIT: Believe the max modulation speed the driver IC could do is 1MHz, but it would be lower due to other component restrictions.
Last edited:
- Joined
- May 24, 2009
- Messages
- 53
- Points
- 8
Nice link, very informative thread. really would like to get a few of those LASORB when
available. wish they were surface mount or tied in with the laser diode can. that would be sweet!
I do need a couple more for another build so it looks like i am doing this one again.
i also contacted aixiz and they might have a couple longer enclosures so can fit my wires in there i hope. this will be nice especially when i put the enclosed driver within the tec block
all powered with a single 5v source. just not sure how good the modulation will be since i haven't heard from them.
i would also like to change power supply to a laptop type wall charger so i can make my projector really small.
I think your right on the LM358N chip cause when i passed the high resistor it measured 1.2 amps output. and everything else looks similar. Now i just need to insure my power supply has a soft start.
available. wish they were surface mount or tied in with the laser diode can. that would be sweet!
I do need a couple more for another build so it looks like i am doing this one again.
i also contacted aixiz and they might have a couple longer enclosures so can fit my wires in there i hope. this will be nice especially when i put the enclosed driver within the tec block
all powered with a single 5v source. just not sure how good the modulation will be since i haven't heard from them.i would also like to change power supply to a laptop type wall charger so i can make my projector really small.
I think your right on the LM358N chip cause when i passed the high resistor it measured 1.2 amps output. and everything else looks similar. Now i just need to insure my power supply has a soft start.
Last edited:
diachi
0
- Joined
- Feb 22, 2008
- Messages
- 9,700
- Points
- 113
I have all the components for the stam_ham driver on my desk ATM. Total cost of components was a little over £5.
I'll make a start on it tonight maybe.
Hopefully getting a new case for my projector too ! The one I have is big enough to fit in a full two level 1W RGB, and still have space. Shrinking down to a dell Optiplex 260/70/80
I'll do some work on that driver and get back to you guys !
I'll make a start on it tonight maybe.
Hopefully getting a new case for my projector too ! The one I have is big enough to fit in a full two level 1W RGB, and still have space. Shrinking down to a dell Optiplex 260/70/80
I'll do some work on that driver and get back to you guys !
- Joined
- May 24, 2009
- Messages
- 53
- Points
- 8
stan_ham
are you going to use the bd437 board ?
what are the voltage in limits of this pcb design?
this is my layout plans:
my scanners, power supply etc. ya i know they are budget versions lol
i would like to use the same 24v out from the scanner amp and wired to my variable voltage regulator:
use this as my power input to my stan_ham board.
if that works we could integrate a new pcb design all built in with a few bells and whistles.
just not sure on how much current this driver requires.
definitely keep me posted.
are you going to use the bd437 board ?
this is my layout plans:
my scanners, power supply etc. ya i know they are budget versions lol
i would like to use the same 24v out from the scanner amp and wired to my variable voltage regulator:
use this as my power input to my stan_ham board.
if that works we could integrate a new pcb design all built in with a few bells and whistles.
just not sure on how much current this driver requires.
definitely keep me posted.
- Joined
- May 24, 2009
- Messages
- 53
- Points
- 8
ill hit u up on this idea since your helping me out
http://cgi.ebay.com/Military-Ammo-C...QQptZLHQ5fDefaultDomainQ5f0QQsalenotsupported
http://cgi.ebay.com/Military-Ammo-C...QQptZLHQ5fDefaultDomainQ5f0QQsalenotsupported
diachi
0
- Joined
- Feb 22, 2008
- Messages
- 9,700
- Points
- 113
Yeah I'll be using the BD437 , I've got it mostly wired up now, just a few things to finish which I'll do later , and then hope that I've done it all right ! 
If I get this one working I'm going to etch a few boards and then build them into that and see how it goes. And then maybe build a 400mW red setup for my scanner to go with my green 100mW.
I don't know the limits of the stan_ham board. But I do know that you may not be able to power it off of your scanner PSU. Mines is 30V voltage differential at 800mA, so it's not good for powering much other than the scanner amps and DMX board due to current restrictions.
Send me a PM and we can talk if you want
Regards,
Adam
If I get this one working I'm going to etch a few boards and then build them into that and see how it goes. And then maybe build a 400mW red setup for my scanner to go with my green 100mW.
I don't know the limits of the stan_ham board. But I do know that you may not be able to power it off of your scanner PSU. Mines is 30V voltage differential at 800mA, so it's not good for powering much other than the scanner amps and DMX board due to current restrictions.
Send me a PM and we can talk if you want
Regards,
Adam
Last edited:
