jayrob
0
- Joined
- Sep 21, 2007
- Messages
- 9,862
- Points
- 113
UPDATE!
I am now selling the Pocket Mini Kit for DIY! Host, heatsink, prep. the 'pill'. See here!:
http://www.laserpointerforums.com/forums/YaBB.pl?num=1231664443/0
No longer selling complete builds... Please read this:
http://www.laserpointerforums.com/forums/YaBB.pl?num=1231511226/0
Looking for a nice mini laser? This is a great little host with a tail button clicky switch.
(Host size - 3/4" X 3") The 'Pocket Mini' is a really nice build! It runs off of a single 3.0 volt Lithium primary, or a 3.6 volt Lithium rechargeable battery. Check out the size!
Using quality parts...
* FlexDrive driver
* Custom heatsink
* AixiZ acrylic module
* 803T blu-ray or 'long' open can red diode.
It's nice to have the option to use primaries, or rechargeable batteries!
Heatsink: The thickness of the heatsink is not bad for such a small host...
Although this host is shorter than a AA host, it is just a little 'thicker' (larger in diameter), to suit the CR123 battery. So the heatsink is pretty nice for the 'Pocket Mini'!
The build is very solid! As seen in the pictures, the heatsink, driver, and module/diode, are all installed inside the head of the host. They are screwed into place, holding these parts solidly fixed, inside the head, adding to the heasinking properties of this design!
Really a nice finish! Very 'weighty' in your hand for the size of it. I really like this little 'Pocket Mini', it has become my current favorite!
I think that there is plenty of heatsinking for 115mW's of blu-ray... Or, 225mW's of red!
(Beam shots - with some smoke)
Holster! I found a really nice accessory for the Pocket Mini!
This black leather holster is nice and thick! It is made for a MiniMag. The 'Pocket Mini' will slide in 'snug', then you just stretch the leather a little by pressing your fingers on the sides (each side), like so...
Then it is 'form fitted' for your Pocket Mini!
Here's the link for the holster: http://maglitesales.com/maglitestore/Holsters/Maglite-AA-Mini-Mag-Holster-Leather-AM2A026
Here's the host: http://www.dealextreme.com/details.dx/sku.5963
Jay
My Key Chain Laser Build - Must See!:
http://www.laserpointerforums.com/forums/YaBB.pl?num=1230765788/0
Check out my DIY Green Laser Build!:
http://www.laserpointerforums.com/forums/YaBB.pl?num=1227233016/0
I am now selling the Pocket Mini Kit for DIY! Host, heatsink, prep. the 'pill'. See here!:
http://www.laserpointerforums.com/forums/YaBB.pl?num=1231664443/0
No longer selling complete builds... Please read this:
http://www.laserpointerforums.com/forums/YaBB.pl?num=1231511226/0
Looking for a nice mini laser? This is a great little host with a tail button clicky switch.
(Host size - 3/4" X 3") The 'Pocket Mini' is a really nice build! It runs off of a single 3.0 volt Lithium primary, or a 3.6 volt Lithium rechargeable battery. Check out the size!
Using quality parts...
* FlexDrive driver
* Custom heatsink
* AixiZ acrylic module
* 803T blu-ray or 'long' open can red diode.
It's nice to have the option to use primaries, or rechargeable batteries!
Heatsink: The thickness of the heatsink is not bad for such a small host...
Although this host is shorter than a AA host, it is just a little 'thicker' (larger in diameter), to suit the CR123 battery. So the heatsink is pretty nice for the 'Pocket Mini'!
The build is very solid! As seen in the pictures, the heatsink, driver, and module/diode, are all installed inside the head of the host. They are screwed into place, holding these parts solidly fixed, inside the head, adding to the heasinking properties of this design!
Really a nice finish! Very 'weighty' in your hand for the size of it. I really like this little 'Pocket Mini', it has become my current favorite!
I think that there is plenty of heatsinking for 115mW's of blu-ray... Or, 225mW's of red!
(Beam shots - with some smoke)
Holster! I found a really nice accessory for the Pocket Mini!
This black leather holster is nice and thick! It is made for a MiniMag. The 'Pocket Mini' will slide in 'snug', then you just stretch the leather a little by pressing your fingers on the sides (each side), like so...
Then it is 'form fitted' for your Pocket Mini!
Here's the link for the holster: http://maglitesales.com/maglitestore/Holsters/Maglite-AA-Mini-Mag-Holster-Leather-AM2A026
Here's the host: http://www.dealextreme.com/details.dx/sku.5963
Jay
My Key Chain Laser Build - Must See!:
http://www.laserpointerforums.com/forums/YaBB.pl?num=1230765788/0
Check out my DIY Green Laser Build!:
http://www.laserpointerforums.com/forums/YaBB.pl?num=1227233016/0