Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

FS: ***MXDL Custom Machined Heatsinks***

Re: MXDL Custom Machined Heatsinks

desslok said:
Yeah fits perfectly.  But I knew it would after seeing all your pics.  Really nice colored instruction sheet too.  The nicest instruction sheet of anything I've bought recently lol.  The set screw is nice, because I would probably have used thermal epoxy if not, and would never have been able to get it out.   Now I can just use thermal compound. Like I said, I already killed a diode from heat.  Running a little over 300mA, left on a little too long and the little hair wires connecting to the actual chip melted off the chip. Dont' want that to happen again.  Thanks again!
Click to expand...

Good news Steve. Yeah, the only reason that it wouldn't fit perfectly, is if there may be some slight differences in the MXDL batches or something. Good idea with just a little thermal compound. Thanks for the compliment on the instruction sheet! Here's a link to the .doc file if anybody wants to take a look at some install details and notes on fitting the DDL driver:
http://www.sonic.net/~jayrob/MXDLHeatsinkTips.doc
Jay
 





Re: ***MXDL Custom Machined Heatsinks***

chido said:
Hey Jay, I got a question. When you used to make the heatsinks without the screw and you had to press the module in with a vice, how wide did you make the hole so that the aixiz modules had a tight fit?
Click to expand...

I used a 29/64 drill bit, which is a tad smaller in diameter than the AixiZ modules. Then, you have to use emery cloth wrapped around something like a phillips screwdriver to sand the I.D. while it is turning in the lathe. The set screw is the way to go! Easy install. Also, easy to replace the diode!
Jay
 
Re: ***MXDL Custom Machined Heatsinks***

Ok, thank you for your answer. :)
 
Re: ***MXDL Custom Machined Heatsinks***

Jay, could you post the dimensions of your heatsinks?
it looks like there are a couple of lengths, and 2 or 3 outside diameters there that would describe them.

I may be interested in one or two, think they might fit in a body I already have.

Thanks!

DanQ
 
Re: ***MXDL Custom Machined Heatsinks***

danq said:
Jay, could you post the dimensions of your heatsinks?
it looks like there are a couple of lengths, and 2 or 3 outside diameters there that would describe them.

I may be interested in one or two, think they might fit in a body I already have.

Thanks!

DanQ
Click to expand...

Edit: Picture showing heatsink dimensions removed.

A couple of people have copied some of my stuff not for personal builds, but to sell right alongside me. So I have decided not to share measurements for my stuff anymore. It's a sad thing, but the bad people mess it up for the good people...
 
Last edited:
Re: ***MXDL Custom Machined Heatsinks***

danq said:
Cool! Thank you!
:-)
DanQ
Click to expand...

Your welcome! Just let me know if you decide that you would like one...
Jay
 
Re: ***MXDL Custom Machined Heatsinks***

toked323 said:
yea but with this no dummy is needed
Click to expand...

I know, its a smart idea. but, where do you charge 14650's?
 
Re: ***MXDL Custom Machined Heatsinks***

:'( rats... just checked - mine is just a tad smaller. What I'd need is diameters <25mm , 26.5 mm, 22mm, same lengths.
Guess I'll have to punt...

DanQ
 
Re: ***MXDL Custom Machined Heatsinks***

amkdeath said:
[quote author=toked323 link=1202452073/30#42 date=1203132071]yea but with this no dummy is needed
Click to expand...

I know, its a smart idea. but, where do you charge 14650's?[/quote]
you get one of these here!
(that's the direction I've been headed for my burner)
 
Re: ***MXDL Custom Machined Heatsinks***

danq said:
[quote author=amkdeath link=1202452073/30#43 date=1203132159][quote author=toked323 link=1202452073/30#42 date=1203132071]yea but with this no dummy is needed
Click to expand...

I know, its a smart idea. but, where do you charge 14650's?[/quote]
here!
(that's the direction I've been headed for my burner)[/quote]


nice man! go for it and tell us how it comes out!
 
You must log in or register to reply here.


Back
Top