Fs - case arm and alum plate

[andy_con]

Fs - case arm and alum plate

couple of ramdon items for sale but im hoping someone can make some use of them.

6mm thick alum plate measuring 275mm by 185mm. has some holes in it

looking for £15 + postage

laser case arm made from 2.5mm thick steel. the tube is 3mm thick.
width of the arm is 200mm, height of the arm to the centre of the holes is about 75mm. the tube is 100mm long and diameter is 33mm across.

made to a very high quality and cost me £20, i would acceot £15 for it + postage

 

[diachi]

Re:  Fs - case arm and alum plate

couple of ramdon items for sale but im hoping someone can make some use of them.

6mm thick alum plate measuring 275mm by 185mm. has some holes in it

looking for £15 + postage

laser case arm made from 2.5mm thick steel. the tube is 3mm thick.
width of the arm is 200mm, height of the arm to the centre of the holes is about 75mm. the tube is 100mm long and diameter is 33mm across.

made to a very high quality and cost me £20, i would acceot £15 for it + postage

Think I could fit an RGB on the aluminum plate, or at least the optics part of it ?

 

[andy_con]

Re:  Fs - case arm and alum plate

yeah?

 

[diachi]

Re:  Fs - case arm and alum plate

yeah?

Hate to question the master, but are you SURE ?  :-X   Cause I need a base plate to start my case off with.


EDIT: I mean like a 0.5W RGB btw .

 

[andy_con]

Re:  Fs - case arm and alum plate

am i sure what??

i didnt say you could fit anything on it, you did LOL

 

[diachi]

Re:  Fs - case arm and alum plate

am i sure what??

i didnt say you could fit anything on it, you did LOL

I asked if you thought I could fit the beam table for an RGB ( 0.5W ) on it and you said " Yeah? " ;D

this may get confusing

 

[andy_con]

Re:  Fs - case arm and alum plate

LOl you said


Think I could fit an RGB on the aluminum plate, or at least the optics part of it ?

you didnt say - do you think i could fit ***** onto the plate.

so i just replied yeah

im building a full RGV 20k scanner on one level, on a board half the size of that. it all depends on the size of your parts and how you lay it out.

 

[diachi]

Re:  Fs - case arm and alum plate

LOl you said


Think I could fit an RGB on the aluminum plate, or at least the optics part of it ?

you didnt say - do you think i could fit ***** onto the plate.

so i just replied yeah

im building a full RGV 20k scanner on one level, on a board half the size of that. it all depends on the size of your parts and how you lay it out.

True  

I think I'll just make one, I have access to a machine shop anyway. What's the dimensions of your current 1W RGB setup ? I was considering using a similar beam table layout .

thanks  

-Adam

EDIT: sorry for sending your thread off topic :-X

 

[andy_con]

Re:  Fs - case arm and alum plate

pffffffffffffff dont make me get up to measure it............

its two level and something like 300mm by 350mm, height is something like 300mm

 

[diachi]

Re:  Fs - case arm and alum plate

pffffffffffffff dont make me get up to measure it............

its two level and something like 300mm by 350mm, height is something like 300mm

Ha ! I guessed that pretty close, no need to measure it though I guessed it was 320 wide 280 deep and 320 tall.

thanks a lot man!

-Adam

 

[andy_con]

Re:  Fs - case arm and alum plate

no problem.

these parts are/were from my 300mw 30k scanner

 

[diachi]

Re:  Fs - case arm and alum plate

no problem.

these parts are/were from my 300mw 30k scanner

Is this the soon to be 1.4W 30K scanner ?

 

[andy_con]

Re:  Fs - case arm and alum plate

sure is.

well the only part from that scanner will be the 30k scanners.

 

[diachi]

Re:  Fs - case arm and alum plate

sure is.

well the only part from that scanner will be the 30k scanners.

Can't wait to see it !! good luck with the build

 

[andy_con]

Re:  Fs - case arm and alum plate

Can't wait to see it !! good luck with the build

you and me both