Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

DIY driver help

F

furrylaser

0
Joined
Aug 20, 2011
Messages
37
Points
0
so i read the thread about diy drivers, and i have a few questions.

Lets say i want to power a 445nm diode up to 1000ma. would i need to put one 1 ohm resistor or ten 10 ohm resistors?


Edit: Also would it be better to just buy a driver to power the diode?
 
Last edited:





r = v/i

lets sat you feed it 4.5 volts and you want to drive it at 1 amp

r = 4.5/1

You need a 4.5 ohm resistor to drive a diode at 1 amp assuming your voltage is 4.5 volts.

EDIT:
If you have 2x 10 ohm resistors on hand, put them in parallel (or 5x 1 ohms in series) and that will give you a 5 ohm resistor
 
Last edited:
What driver are you thinking of using, mister furrylaser?

Jacob32123 said:
r = 4.5/1
Click to expand...

V should be the voltage drop across the resistor, not the supply voltage.

What about if the supply voltage was 2V and we used that equation? It would suggest 2 ohms when in fact NO value of resistor will will allow any current through the diode, because 2V isn't enough.

The forward voltage of a 445nm at 1A is about 4.5V. So if your supply voltage was 4.5V, you wouldn't need a resistor.

That's theory, but in the real world, you cannot be sure that either the voltage of the diode or the voltage of the power supply will be exactly 4.5 all the time, and small changes in voltage make for large changes in current.
 
Last edited:
I was thinking about making my own driver, using a LM317 regulator. Also which kind of variable resistor would i need on it? This is my first "high" powered laser.
 
the wires going to the diode or to the battery?

also do you have to do this everytime after you set the current with a test load?
 
I rather not call you "furry," unless you are lol.
Anyway, I'm doing the same thing too. I just bought the beefiest potentiometer I could find. I think mine is a 5W wire wound pot lol. Not taking chances with the potentiometer frying and putting my power control out of commision. Anyway I've used it on my breadboard with no probs. try that.
 
ok so i got a 1w 445 diode from 5.6mm 445nm ~1W laser diode [M0020] - $51.99 : Modwerx Shop and i pressed it into an aixiz module and am using a glass 445nm lens. Now for the driver, i was thinking about making one with the lm317 regulator. I just have a couple questions, how much voltage does the diode need? I am going to use a 9 volt power supply and how many resistors do i need rated at how many ohms?I used the r=v/i and so r=9/1.2 (i decided to power it at 1.2 amps) and got 7.5. So do i need a 7.5 ohm resistor? Also do i need a capacitor? Lastly i don't really get what a potentiometer does i think it regulates the current but then how do you know how high of a potentiometer you need?

thank you
 
Last edited:
furrylaser said:
ok so i got a 1w 445 diode from 5.6mm 445nm ~1W laser diode [M0020] - $51.99 : Modwerx Shop and i pressed it into an aixiz module and am using a glass 445nm lens. Now for the driver, i was thinking about making one with the lm317 regulator. I just have a couple questions, how much voltage does the diode need? I am going to use a 9 volt power supply and how many resistors do i need rated at how many ohms?I used the r=v/i and so r=9/1.2 (i decided to power it at 1.2 amps) and got 7.5. So do i need a 7.5 ohm resistor? Also do i need a capacitor? Lastly i don't really get what a potentiometer does i think it regulates the current but then how do you know how high of a potentiometer you need?

thank you
Click to expand...
A potometer is a variable resistor
I'm on my way home from school and ill give you a link that will help a lot
 
You must log in or register to reply here.


Back
Top