Search results

Thank you Jander6442, at least I did (tried to do) my best. Thanks :) My next one I think will be something (I would like to be) like your 12x saik. Now I want a 405nm. :)

I turned it on for 1 minute and it became a little warmer. after 1 minute off it had again the normal temperature. so, maybe it is 1 minute on - 1 minute off. A bit confused.

When I enjoy it a little I will send it Eytyxhs. Thanks :)

You are right. This is the problem with the small hosts finally. Some more information that I forgot to write above is that the batteries the time I got the video were at 3,85 V each and yesterday when it gone out of power I measured the batteries and were at 2,5 V each :) I will try to make a...

I think the same but ...what to do?:thinking: I am not sure about the duty cycle but I like more because you like it too :) Maybe I am wrong about the duty cycle (I hope). But if the duty cycle is good I do not hope to be wrong :)

Thank you very much The Baron. I feel my happiness to need a heatsink because overloaded :)

I am glad you like it Eytyxhs :) gg :) If people like you and Blord like it, I am very happy. !

I did it :). If you like to see it, it is here: http://laserpointerforums.com/f65/445nm-9mm-diode-2-1-x-driver-c6-host-77745.html#post1118320

Thank you Blord :)

Hi all :wave: After so much reading, research and time I builded this. I could build it 2 months ago as I had almost all the parts but some problems in my life forced me to do it now (it is better late than never). I have to apologize for my bad quality photos, I got them with a mobile phone...

yes. with extension to can get 2 batteries IMR 18650, and some cutting in this aluminium part that fits the ring that holds the blank board (I do not remember now its name). copper heatsink (for the diode module but and for the driver) and I think (I will be 100% sure when I finish it) that it...

...and I forgot to say about the blank board. is PERFECT. The best dimensions for a c6 host.

I got the driver before 12 hours about but I had no time to see it untill now. Now I seen it of course and as I expected this driver is truly the best, or maybe just perfect. And not only for the driver but and for the packaging in the ESD bag and for the silicon wires that gave to me and for...

I ordered some parts before some days and I received the package today. I have to say that everything was something more than a simple ok. Gary is very helpful, good packaging, fast shipping and some parts are very better than what they looks by a simple photo (host, googles, ....). Thanks...

Hi all. I got a pair of these goggles and I like them very much. The design is awesome but I noticed that the photos that present the goggles are only from the front view. I searched everywhere and I didn't see any photos of these goggles from the back or side view. So if there is somebody that...

Re: BlitzBuck V3, Available Soon! It is jumpered from the right side of inductor to the bottom of capacitor. I couldn't take a better pic from my mobile. So, like you said, it is not a problem. But... I will take your advice to remove it (safest way anyway, and better aesthetic look). So, now I...

Re: BlitzBuck V3, Available Soon! Hi all. Wolfman I need your "lights":can: here. Today I got 3 blitzbuck v3 and I noticed that there is a short here (but maybe not problem) to the first of them. I think that I must get out this solder from there but maybe it does not matter cuz maybe there is...

HI Larry. I sent to you a pm. Did you receive it?

oh, yes. i got my stuff...... And thank you again Jim. Everything is ok. :)

YES !, This option I was hoping to see so much time. This diode with its correct copper module, together. The time of 9mm diodes lasers has come :) (now I am impatient to see this option available.):)