Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

How to Register on LPF | LPF Donations

Search results

  1. mark-in-dallas

    Vapers

    I'm using the Sony 18650 VTC5. 2600mAh with 30 Amp max continuous discharge rate, and bursts up to 60 Amps. I haven't actually taken an ammeter to the circuit, but judging from how it performs it does appear to be pretty close. The Steam Turbine Atomizer pictured on it ohms out at .77, and...
  2. mark-in-dallas

    Vapers

    OK, so any serious vapors have probably already heard of the Evolv DNA 30 chipset which can run atomizer resistances as low as .4 ohms and as high as 30 watts, and there are already a number of mods available with the chipset if you don't mid getting on a waiting list or putting in a pre-order...
  3. mark-in-dallas

    Vapers

    With the Vamo V3 and V4 you can also drill through 1 or 2 of the indentations in the top cap to allow increased airflow, instead of cutting grooves into the tanks. I hope one of these works for you.
  4. mark-in-dallas

    Vapers

    If the bottom of the tank sits to flush with the mod it may be blocking airflow, causing you to have to take harder hits to bring the air into the atomizer and vaporize. You may also notice that there isn't much vapor production. In order to allow enough air into the tanks I cut grooves into...
  5. mark-in-dallas

    Vapers

    I am not a doctor, but the symptoms sound like something other than your body not liking one of the ingredients in the smoke juice. I'm thinking something more along the lines of possible muscle strain from how you may be taking hits on it. You might try taking longer slow and easy hits...
  6. mark-in-dallas

    Vapers

    Not as nice as the Vamo, but not bad. It's a variable voltage too running from 3V to 6V, but I don't think the current can be driven above around 3A or so. The button kind of sucks too because it can be hard to find without actually looking at it. Not much different than an Ego Twist, except...
  7. mark-in-dallas

    Vapers

    Virtually any rebuildable atomizer can be used for making the connection between the diode and vape mad, or you can tear apart a cartomizer and use the internal coil wiring for the connection as well. I just tried taking a picture of my Vamo V3 powering the Eternity Atomizer/Laser mad, but...
  8. mark-in-dallas

    Vapers

    Yep, I had the same thought and modded my Vision Eternity atomizer into a portable laser module. :)
  9. mark-in-dallas

    Vapers

    For smoke juice give ecblend.com a shot. They have a ton of flavors and the best prices on smoke juice I''ve seen in the U.S. And some real unique flavors too! Mods, atomizers, batteries, clearamizers, etc. look to fasttech.com. Fast shipping for a Chinese company, great selection and...
  10. mark-in-dallas

    SOLD - 1,750 mW 445nm Ultrafire C5 Bullet

    Nope just sold it, sorry guys.
  11. mark-in-dallas

    No longer FS - 400mW 405nm - Ultrafire WF-C6S

    Re: FS - 400mW 405nm - Ultrafire WF-C6S Well, I was going to check it and let you know, but after about a minute the diode went LED. Oh well! But, at the one minute mark the copperr heasing had not warmed up much. So, this puppy's off the table, and I'll probably rebuild it with a 445nm.
  12. mark-in-dallas

    No longer FS - 400mW 405nm - Ultrafire WF-C6S

    Re: FS - 400mW 405nm - Ultrafire WF-C6S It uses a felxdrive. Also, I don't have anymore spare glasses, so price they will no longer be included and I will drop the price to $110.
  13. mark-in-dallas

    [FINALLY SOLD] FS: "The Copperhead" 375mW 635nm Pocket Stainless Steel

    Re: [$120!] FS: "The Copperhead" 375mW 635nm Pocket Stainless Steel You are of course welcome! And BTW, not sure if you mentioned it or not, but this laser has a twisty switch, and what's kind of cool is that if you turn it till the laser comes on then back it off about a 1/4 turn, you've got...
  14. mark-in-dallas

    SOLD.!!! 1.5W 445nm Laser in a Stainless Steel Classy Host "Steel Wave"

    Re: FS: 1.5W 445nm Laser in a Stainless Steel Classy Host "Steel Wave" And laseerer kicks out another beauty! Nice!
  15. mark-in-dallas

    [FINALLY SOLD] FS: "The Copperhead" 375mW 635nm Pocket Stainless Steel

    Re: [$120!] FS: "The Copperhead" 375mW 635nm Pocket Stainless Steel I also put together a build in that host, except mine is a 445nm, and it is one of my favorites. Tiny, tiny, tiny! For anyone that likes the smaller builds, I believe this is the tiniest there is! Even smaller than my F-23...
  16. mark-in-dallas

    1.3W Ehgemus Build $165 SOLD

    Re: 1.3W Ehgemus Build $165 Nice build Luke! BTW, Mothers Mag & Aluminum Polish works wonders on making Ehgemus hosts shine like new and it's just a couple of bucks at Walmart.
  17. mark-in-dallas

    SOLD 2W or 1650mW Aurora Sh-032 445nm

    Re: FS 2W or 1650mW Aurora Sh-032 445nm Still available!
  18. mark-in-dallas

    SOLD 2W or 1650mW Aurora Sh-032 445nm

    Re: FS 2W or 1650mW Aurora Sh-032 445nm That's my favorite part about building lasrers: finishing one and LPM'ing it to see how efficient the diode turned out to be. Then again, it kind of bums me out a bit when I find ones running less thean 80% or so. My worst LPM'd at under 70% or the...
  19. mark-in-dallas

    SOLD 2W or 1650mW Aurora Sh-032 445nm

    Re: FS 2W or 1650mW Aurora Sh-032 445nm I thought I saw that it was set to 1.4A. :) Still a very efficient diode though! I think I've only had 2 diodes that were over 100% efficient, and one of them is in a Trustfire F23 set at 1.1A and outputting 1.35W. Driver is . You should probably...
  20. mark-in-dallas

    SOLD 2W or 1650mW Aurora Sh-032 445nm

    Re: FS 2W or 1650mW Aurora Sh-032 445nm The adjustable pot versions are very easy ti set, run nice and cool and working with them is a snap. I think you'll really like them. I've got a couple fixed at 1.8A. If you don't have eny and want to try one, shoot me a PM with your shipping info and...


Back
Top