Search results

Nope. What you're talking about is second harmonic generation. Two photons of the same wavelength come in, and through some fancy quantum mechanics out pops one photon that's half the wavelength. There are so many variables getting any kind of efficiency out of this that you are much better...

I have a Coherent FAP housed in the full module with monitoring and TEC. The FAP is in pretty bad shape (emits 3W @ 30A). I have another FAP I want to swap in and reuse the TEC. I've removed most of the module but the FAP is bonded to the heat spreader with a thin sheet of indium foil and I...

Selecting parts is really hard -- there are so many. But unless you have specific needs (high power, fast switching, low noise) there are some standard parts you can start with. For op-amps, Dave on the EEVBlog has a good video on what he calls "jelly bean op-amps", which are generic, common...

I designed a control board that can do 53 amps 4v into two channels each for a dual end-pumped z-fold cavity. It's switch mode based on the MAX20096. It uses some pretty beefy MOSFETS and inductors and has a switching speed of 1Mhz so it's pretty clean. Can run on a 2s LiPo pack but it's...

I did try inserting a 1/2 wave plate and rotating that -- there was a small (5%) improvement depending on orientation. I haven't tried rotating the whole fiber. These FAPs have random polarization so they will lose some efficiency here for sure. The Verdi's use them into vanadate too so I am...

If you have a power meter you can test how well your current goggles work: defocus the laser and shine a somewhat broad beam through a pair of goggles and measure what comes through on your power meter. If that transmitted power is <= class 1, your current goggles are fine. Just be sure to wear...

Ok, so for the last couple of years I've been working on building a portable DPSS laser. It's a Z-fold cavity design powered by two 40W FAP modules. All electronics are battery operated by an integrated LiPo pack. At full tilt there is enough battery to run it for about 30 minutes. It's portable...

(Sorry, totally misread your question). No specific plans other than to learn how to do it and see what kind of power level I can achieve. I will frequency double it to green, and I want to try passive Q-switching once I understand enough to be reasonably confident I'm not going to ruin...

Z-fold is lasing! Only took me about seven hours to align it and still only using one pump. But it's miller time.

Thanks for this, it's great data and will come in handy as I dial in the z-fold. I figured out my alignment confusion. Well, I got some help from folks along the way. The alignment beam is going to deflect from the crystal for all sorts of reasons (crystal not totally parallel, refraction...

:) Ha. Been there, done that. I have plenty of things that pew pew. This one...this is more of a journey. And my wife hoping someday I will talk about something else. whysoserious - FAPs are Coherent FAP 40w. They are used but in good condition and temperature tuned to emit @ 808. I don't...

I've spent some time on this and no luck. First, my idea of using the IR leakage from my 532nm pointer is not going to work. Yes, it's cheap and leaks IR. But is just "spill" from spontaneous emission and not in the beam. If I put a visible block filter in front of it I get next to nothing...

This video shows a neat technique: Wavelength Division Multiplexing. He's using knife edging, but also a TEC cooler on each end of a group of diodes to create a temperature gradient. Since wavelength is temperature dependent, you can then take the independent beams from the knife edge array...

Thanks Tony. Will spend a few nights this week trying this out. Your green laser sparked an idea -- I have a cheap DPSS 532nm laser that spits out a bunch of 1064 light too. I have not been using it for alignment because while the label says < 5mw, my LPM says it's putting out about 60: way...

#2 is a planar mirror that's HR 1064 HT 808. But the black cylinder to the left is a combination collimator and focusing assembly. It's currently set to about 300um but with a lens swap I can get it down to about 150um at the crystal face. Unfortunately the light coming into this is a fiber...

I've been working on a DPSS laser for a while now. My goal is a frequency doubled Z-fold pumped by two 40w FAPs. I've done a ton of work on this, from designing my own power supplies and TEC controllers, to modeling the cavity via software to ensure stability and a decent beam waist in both the...

Another update: some level of success. Little white dot on the white IR target is a 1064nm laser beam at about 2 watts: Glamor shot: The whole apparatus: Lots more to do. Only about 5% wall plug efficiency, need to convert to green, and need to convert to a z-fold so I can double-end...

Progress Update: I spent a fair amount of time designing a TEC controller...and then designing another one that could handle higher currents because the 5A I was sending to the TEC wasn't enough to keep the FAP cool. Yes, it is a little concerning that it may take more power to cool the FAP...

@Alaskan I'm wondering if you ever got the Spectra Physics ZLM to lase? I have a working TEC now so I can keep the FAP temperature in check and I'm trying to get the ZLM to lase but no luck. I'm only using one FAP -- do you or anyone else know the ZLM threshold? The output from the fiber...

I'm starting to think the harmonic separator is the way to go. This is basically a mirror that only reflects 532 so you can keep the 532 in the KTP section of the resonator. This opens up your options a bit as every mirror in the resonator doesn't need to be both 1064 and 532. And yes...