Search results

I don't do any anodizing... That's something you would need to get done elsewhere, but the silver Mag host is a nice match to the machined bare aluminum...

I followed the instructions from the driver manufacture with no questions asked. (Angelos) For this specific set up (C-mount red), he wanted an extra layer of safety is what I figure... About the 7 Amps, I did not test. Again, this was told me from Angelos. That it can do that. Obviously the...

New month, April. Donation sent... Thanks for the great forum Avery! :beer:

I believe it is just like his normal X-Drive except that it has ramp up slow start and can adjust easily to 5 Amps, and even up to 7 Amps per Angelos... For this C-Mount red which is a case positive diode, you still need to isolate the diode. Here's a picture of how I set it up in a case...

He now has a new 'slow start' X-Drive that can do up to 7 Amps adjustable... :)

Yes... Send me a PM! :beer:

Yes I'll send you a PM... :beer:

I recommend an M-140 @ 1.5 Amps for this build just because of the battery capacity, etc... 'Hot' option means that the driver is installed, current set, lead wires ready for your diode. It can be assembled in 5 or 10 minutes... Proper eye protection needed. I'll send you a PM... :beer:

For what is in that list yes... Send me a PM! :beer:

New month, March. Donation sent... Thanks for the great forum Avery! :beer:

I have a nice SolarForce kit and I've seen longer ones that hold 2 X 18650 cells... http://laserpointerforums.com/f64/fs-solarforce-l2p-kit-18650-host-massive-heatsink-53746.html Send me a PM! :beer:

Shouldn't really call it a G2 if it is a different optic... I have already had one person ask me to machine just the lens barrel for a G lens, but if this is a different optic vs G1/G2, then it will not fit the same... Wonder what they are? Guessing maybe G9 from projectors?? Since G1/G2...

Yes I'm doubting that these are the same optic as G1/G2 and should be called something else... Guessing maybe G9 from projectors?? By the way, G1/G2 are still available...

Hey Hak I would like to see if you can verify that this lens from AixiZ is in fact a G2 optic or is it something similar? The reason is because a member contacted me to make him just the lens nut for the G2 lens, but I'm guessing that this lens is not actually G2 because it is too cheap to be a...

I'll send you a PM... All good except I recommend a 2 cell build at that power... And make sure you get proper eye protection for 445 if you don't already have some... :beer:

A while back I showed a tread on how to make something similar or better with a Maglite with parts listed... :beer: (easy build) http://laserpointerforums.com/f39/sold-mag-623-100-watt-flashlight-mod-70138.html

Re: FS: 1000 Lumen XM-L U3 Maglite Mod With Voltage Monitor - Parts, or Complete Ligh Sure I can send a heatsink/emitter/driver combination but you would still need to do the switch mod and reflector mod shown in the thread... Send me a PM! :beer:

For a 3D Mag, you can use an XML emitter / 3 X NiMH cells / and the same driver shown here: FS: 1000 Lumen Vintage Eveready XM-L U3 Mod!!

New month, February. Donation sent... Thanks for the great forum Avery! :beer:

Yes I still offer the 'Hot' option kit... Couple things... There is not room for a full length module where the module needs to be mounted. So you need the diode in module. (but remove the back 'barrel' part of the module) I mount the driver in a separate location, and you just connect my...