LPF Donation via Stripe | LPF Donation - Other Methods
Links below open in new window
ArcticMyst Security by Avery
Test loads?
- Thread starter Mrmask
- Start date
- Joined
- Sep 20, 2008
- Messages
- 17,622
- Points
- 113
Hmmmm... Time to do some research and reading....
Try "Test Load" or "Dummy Load" or "Dummy Test load" using
the [Search] button... that might work...
Jerry
Try "Test Load" or "Dummy Load" or "Dummy Test load" using
the [Search] button... that might work...
Jerry
D
Deleted member 8382
Guest
On non linear drivers such as the Flexdrive, you need a test load to simulate the laser diode in order to set the current on the driver before connecting the real diode.
On linear drivers such as all the LM317 or similars based drivers (the DDL driver), all you need is your multimeter as load to set the current. These drivers will keep the current constant regardless of the load, so the multimeter itself will work just fine.
On linear drivers such as all the LM317 or similars based drivers (the DDL driver), all you need is your multimeter as load to set the current. These drivers will keep the current constant regardless of the load, so the multimeter itself will work just fine.
- Joined
- Aug 28, 2009
- Messages
- 1,071
- Points
- 0
Flexdrive's have to have a load connected to them before power is applied. If you connect the diode with a DMM in series to measure the current, you run the risk of the driver being set too high and instantly blowing your LD.
Also, all LD to driver connections need to be soldered. Unless your willing to solder your DMM leads to the LD and driver, you risk a momentary open, even a micro-second open, IE: bad connection, will blow the LD, due to capacitor discharge.
And lastly, the less times you subject your LD to the heat of a soldering iron, the better off your diode will be.(without a test load, you have to solder wires to it to test, then desolder the wires, then resolder again to the driver)
mfo
0
- Joined
- Jul 3, 2009
- Messages
- 3,394
- Points
- 0
Read the guide in my signature.
Thank you Hallucynogenyc and Greenmechanic for the advice.
I tried to read the guide but it really made little sense in this part in question. Was he trying to hook up 6 red diodes and 1 blue in the picture? Or were those extra electronics parts that should or shouldn't come with my driver.
Oh and I look at the first 3 threads that look relevant before posting. After that it's just easier to ask.
I tried to read the guide but it really made little sense in this part in question. Was he trying to hook up 6 red diodes and 1 blue in the picture? Or were those extra electronics parts that should or shouldn't come with my driver.
Oh and I look at the first 3 threads that look relevant before posting. After that it's just easier to ask.
Last edited:
D
Deleted member 8382
Guest
Those 6 things are normal diodes. They have a 0.7V drop, so in order to simulate a red diode which has a 4V drop, we use 6 of them in series
The "blue" thing is a resistor which we use to measure the current with the MM. It's called indirect current measurement, google it for more info.
The "blue" thing is a resistor which we use to measure the current with the MM. It's called indirect current measurement, google it for more info.
mfo
0
- Joined
- Jul 3, 2009
- Messages
- 3,394
- Points
- 0
Those 6 things are normal diodes. They have a 0.7V drop, so in order to simulate a red diode which has a 4V drop, we use 6 of them in series
The "blue" thing is a resistor which we use to measure the current with the MM. It's called indirect current measurement, google it for more info.
Actually, red diodes typically have around a three volt drop, so you should be using four diodes in series instead of six. Six diodes are used for blu-rays.
D
Deleted member 8382
Guest
ops, seems like I got confused xD
