Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Does laser 301 series work with CR123A batteries?

Joined
Jul 21, 2017
Messages
4
Points
0
Hello guys, I have a question. Can I use CR123A batteries with my 301 lasers(violet 100mw,green 80mw?

Thanks for reading :)
 





Joined
Aug 23, 2016
Messages
259
Points
28
the 301 and 303 pointers screw apart in the middle and you can take a part off of the battery compartment for use with a 16340 or cr123a's :)
 
Joined
Sep 20, 2013
Messages
17,254
Points
113
IIRC, CR123As are 3 volt batteries. You should be using a 4.2 volt rechargeable battery with the 532nm at least.
 
Joined
Aug 23, 2016
Messages
259
Points
28
IIRC, CR123As are 3 volt batteries. You should be using a 4.2 volt rechargeable battery with the 532nm at least.

i have used a cr123a with my 303 greenie and i dont see any difference at all in brightness or burning capabilities :thinking:
 
Joined
Sep 20, 2013
Messages
17,254
Points
113
Well, whether you notice it or not, there is a difference. CR123As are not rechargeable and measure 3 VDC as apposed to a rechargeable Li-ion battery that will measure 4.2 VDC when fully charged. That is a full 1.2 volt difference, and the 808nm drivers won't output as much power using CR123As.
 
Joined
Jul 21, 2017
Messages
4
Points
0
I see, what about those RCR123 batteries?, I was reading somewhere that those batteries are better than the CR123a since those are rechargeable :)

PD: It is hard to find a good 16340 or 18650 nice battery but the RCR123 batteries it´s easier to find high quality ones.
 
Joined
Sep 20, 2013
Messages
17,254
Points
113
I'm not familiar with the RCR123 batteries, but 16340s are the same size and can be had in 700 mAh capacity. I have some CR123As and they state 3 VDC right on the side.
 
Joined
Sep 12, 2007
Messages
9,399
Points
113
the 808nm drivers won't output as much power using CR123As.

Most of the green drivers I've seen are LDO. With a Vf of ~1.9V, what makes you think 1V or so isn't enough headroom for a LDO? Some of the green drivers I've tested go all the way down to 2.2V while maintaining their current regulation.

I have a couple of these lying around somewhere, so I'll have to test that. Unless the drivers in these are somehow worse than the other chinese stuff, I suspect you're quite wrong.
 
Last edited:
Joined
Sep 20, 2013
Messages
17,254
Points
113
My experience with these cheap 532nm lasers like the 301s and 303s is the drivers in these are not as good at regulating current as well as one might want. For that reason, I have found the output is determined by the input voltage to these cheap drivers. It has nothing to do with the Vf of the pump diode.........just a noticeable difference in the power output when driven with these ubiquitous drivers. Also, the OP is using it for a 405nm and the boost driver in that circuit might be close to cut off at 3 volts.
 
Joined
Sep 12, 2007
Messages
9,399
Points
113
I got around to checking a "303" just now. Mine's fine at low voltage.

4.2V input yields 325mA
2.8V input yields 320mA
2.65V input yields 300mA
 
Joined
Aug 23, 2016
Messages
259
Points
28
nice data cyparagon. so if some drivers are affected by the lower voltage and some arent... has anyone tested something similar with survival lasers 1.25A driver? thats the one that will be in my 638 build and was wondering if the difference in voltage would affect that driver much. im gonna buy myself some 16340s on amazon either way since my local battery store only sells rcr123s and the vape shop nearby overinflates the prices on their batteries.
 
Last edited:
Joined
Sep 20, 2013
Messages
17,254
Points
113
Good drivers should have no effect as they regulate the current to the laser diode. As long as there is enough voltage to drive the diode, it should remain constant. If the battery doesn't have the current to drive a diode, then I'm not sure if the battery voltage will sag, or the driver just won't pull the current and stop regulating.
 
Last edited:




Top