help me with bluray

[AusLasersSuck]

What should I put the MA at for long life (I dont want this baby to die) and what power would it proberly be.

Where can I get these cheaper


want to build
6x burning violet laser ?mw

stuff needed

6x diode/sled where can I buy one

Aixiz module http://www.laserpointerforums.com/forums/YaBB.pl?num=1228038791 4 US

driver 130 ma http://rkcstr.nfshost.com/index.php?main_6x sled http://www.X.com/store/index.php?main_page=product_info&cPath=1&products _id=45page=product_info&cPath=65&products_id=180 16 us

Heatsink http://www.laserpointerforums.com/forums/YaBB.pl?num=1232002100 30 us

Total 106 US.



What ma should I drive at for a nice power and a nice life too?

Where can I get these cheaper


http://www.i-hacked.com/content/view/272/94/

stuff needed

PHR-803T diode http://www.laserpointerforums.com/forums/YaBB.pl?num=1228038791 16 US

driver 110ma http://hacylon.case.edu/ebay/laser_diode/Micro_FlexDrive.php 25 US

Kit http://mysite.verizon.net/grall/darkhorsecustom/id75.html 45 US

Cap http://mysite.verizon.net/grall/darkhorsecustom/id76.html 15 US



Total 92 US.

 

[jayrob]

Looks like you have done some homework already...

Good job.

Now, do now start with a 6X build. First build a few PHR builds. The 6X is too expensive to start with.

If you can get a FlexDrive, that will be 'host friendly'... and work with several different battery supplies.

Dr. Lava is supposed to be getting more in stock soon.

I have a nice host/heatsink 'Pocket Mini Kit' that would work very nice for a blu-ray build. But you must learn to properly adjust current on a FlexDrive using a proper test load. (or buy a pre-set FlexDrive) I like 120 to 130mA's for PHR's. and 180 to 190mA's for 6X's.

Check out the Pocket Mini Kit!
http://www.laserpointerforums.com/forums/YaBB.pl?num=1231664443/0

I also have PHR sleds on hand for $15 dollars plus shipping. (complete sleds only, no harvesting)
Jay

 

[AusLasersSuck]

Looks like you have done some homework already...

Good job.

Now, do now start with a 6X build. First build a few PHR builds. The 6X is too expensive to start with.

If you can get a FlexDrive, that will be 'host friendly'... and work with several different battery supplies.

Dr. Lava is supposed to be getting more in stock soon.

I have a nice host/heatsink 'Pocket Mini Kit' that would work very nice for a blu-ray build. But you must learn to properly adjust current on a FlexDrive using a proper test load. (or buy a pre-set FlexDrive) I like 120 to 130mA's for PHR's. and 180 to 190mA's for 6X's.

Check out the Pocket Mini Kit!
http://www.laserpointerforums.com/forums/YaBB.pl?num=1231664443/0

I also have PHR sleds on hand for $15 dollars plus shipping. (complete sleds only, no harvesting)
Jay

Thanks for the info.

Yea 6x is expensive.

I bought a 110mw bluray im going to make a 5-10 mw bluray lecture pointer with unlimited cycle, a 115 mw dorcy jr laser (proberly gonna sell the dorcy) then a red laser and then a 6x laser with a great heatsink so it will have a good cycle.

 

[brandonw88]

Here is a good place "www dot laser surplus parts dot com" his PHR sleds are only $14 right now.

check out his kits as well he has one that includes a 6x sled