Search results

Re: Mohgasm 1.63A; $10 Each Its a basic linear driver, input voltage need to be diode voltage + ~2.5v generaly you need 2 lithium-ion batts.

Well I have ran a corsair psu at about 110% for 6 months 24/7 during the bitcoin ordeal. What exactly do you mean by switching or linear? If it was linear it would be wasting like 16,000 W lol, Or were you talking about a post regulator mabye?

What makes these any better than a computer PSU? Like this for example?

NEW OFFER: Anyone who buys this kit from me can mail me there finished LPM un-calibrated, and I will calibrate it with a 1.5W 445nm blue laser at 25c against my ophir head Free of charge, Simply include return postage. ***Shipping and insurance for this process is the responsibilty of the buyer

Re: Mohgasm 1.8A, 1.63A; $10 Each Speaking of Mohgasm, Mohgasm is speaking :crackup: 8X 1.62A Left 1.8A is sold out

Re: 2W Small Sun - Stainless Steel 445 Laser Bump.

Or you were being chased by the dot :gun: And if every time a smoker reached for a cigaratte they got a little :lasergun: They would probably quit smoking too lol

At one point you could buy them gold plated, You might be able to find one FS somewhere

Test the resistance between the new chip and one of the old chips on each coresponding pin. Are they all less than 1ohm? yes = dead chip fix by getting a new chip no = bad solder join or bad pcb fix by soldering better or connecting a wire between the pins on the new chip and old chip with a...

Re: 1.3W 445nm Blue Laser, Stainless Steel SH-032 Check your PM's

Re: 1.3W 445nm Blue Laser, Stainless Steel SH-032 Pm'ed Also: Very few people here like WL They have a lot of issues and are known to over rate the lasers they sell http://laserpointerforums.com/f65/33-reasons-not-buy-wicked-lasers-56289.html

Re: 1.3W 445nm Blue Laser, Stainless Steel SH-032 Nope thats not me,

Re: 1.3W 445nm Blue Laser, Stainless Steel SH-032 PM'ed Also I posted pics

Re: DIY LPM "Kit" $40 Using an ophir is a little tricky, but doable 1) Short out all 3 pins on the main adjust pot, (Permanently w/ solder) 2) Grab a 1.5V battery and a multimeter 3) Measure the Battery with the LPM and the multimeter at the same time 4) Make them the same by adjusting the 1X...

Re: DIY LPM "Kit" $50 Kit now for sale.

Nice 1.3W laser in a SH-032 Host Runs on an 18650 (Included) Charger and safety glasses are also included Diode is quite efficient, and has a duty cycle of 2on/1off M140 Diode G2 lens (Optional) (1.3W is with G2 lens; ~1W w/o G2 lens) 1A Aixiz Boost Driver Aluminum Heatsink Copper aixiz...

My next step is to make another revision of the board. I think I will use an SMD Atmega328p I am also going to put the FTDI chip on the board, instead of in the cable. Not sure about my time frame, I start classes on monday. It will depend on how hard they are...

Ya its a coincidence, I had these boards made in July, but was too busy with summer finals to work on them. My adc is 16 bit (15 bit if you consider that my signal should never be negative) and my reference is set to have a range of ~8W Gives me a resolution of 250 uW internally Nope, I'm...

Re: 2W Small Sun - Stainless Steel 445 Laser Deal Extreme

Price is difficult to say right now, but I'm shooting for a price < the Laserbee A Maybe ~200