Old 09-25-2008, 04:23 AM #1
jayrob's Avatar
Class 4 Laser
 
Join Date: Sep 2007
Location: Northern CA, U.S. Astrophotography! (Some of my Photos)
Posts: 9,857
Rep Power: 48222
jayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond repute
jayrob jayrob is offline
Class 4 Laser
jayrob's Avatar
 
Join Date: Sep 2007
Location: Northern CA, U.S. Astrophotography! (Some of my Photos)
Posts: 9,857
Rep Power: 48222
jayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond repute
Default FS: Leadlight Blu-ray / FlexDrive - 126mW's! SOLD

SOLD

This pair of 803T blu-ray pointers are both built with the FlexDrive, and AixiZ acrylic lens. (plastic cut away)



They are just about identical in power and diode efficiency.

I like to keep my blu-rays builds at a fairly conservative power for better longevity. (especially for a pointer) I'm going to keep the one with the brass spacer. (I had to put a spacer in that one because the batteries were too long between switch and cap - maybe the stock circuit was left a little long at the switch)

Up for grabs is the 126mW Leadlight blu-ray pointer! Included with the laser are 2 X AAA Energizer e2 Lithium batteries and dust cap.
$225 plus shipping.

For a little detail on the build, the module is 'press fit' (just tight enough so that I could use my desk top and press it in by hand)...



You can see a couple of sanded down 'solder blobs' on the module. I use this method for two reasons.

* I need a good ground, because in this build, the ground to the driver is through the LD case pin.
* I just like it better than glue... cleaner. Also easier to disassemble if ever needed to swap out the LD.
Jay



__________________
Personal lasers:
(just a few - too many to list) RPL 425, Sypder III Krypton, RPL 35 (473), GLP-473, GLP-593.5, HeNe 632.8,
Many DIY 445, red, blu-ray, green, 635, and 450 builds...


Looking for a DIY kit?


Take a look at some of my more popular kits linked in color...

* FS: 405-G-1 Glass Lens Mod for Blu-ray! 31% increase in power vs AixiZ acrylic!

* FS: New! 1000 Lumen XML-2 Maglite Modification With Voltage Monitor! - Parts or Complete Light! Must see!

* FS: Polished Stainless Steel Green Kit! Easy assembly in minutes!

* FS: Large Maglite Monster Kits! Side Button Forward Clicky! Custom Head Option! Gnarly...


Click here for a list of my build kits! Projects and tutorials too!

jayrob is offline   Reply With Quote


















Old 09-25-2008, 04:43 PM #2
jayrob's Avatar
Class 4 Laser
 
Join Date: Sep 2007
Location: Northern CA, U.S. Astrophotography! (Some of my Photos)
Posts: 9,857
Rep Power: 48222
jayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond repute
jayrob jayrob is offline
Class 4 Laser
jayrob's Avatar
 
Join Date: Sep 2007
Location: Northern CA, U.S. Astrophotography! (Some of my Photos)
Posts: 9,857
Rep Power: 48222
jayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond reputejayrob has a reputation beyond repute
Default Re: FS: Leadlight Blu-ray with FlexDrive - 126mW's

Lowered my price to $225 plus shipping...
Jay
__________________
Personal lasers:
(just a few - too many to list) RPL 425, Sypder III Krypton, RPL 35 (473), GLP-473, GLP-593.5, HeNe 632.8,
Many DIY 445, red, blu-ray, green, 635, and 450 builds...


Looking for a DIY kit?


Take a look at some of my more popular kits linked in color...

* FS: 405-G-1 Glass Lens Mod for Blu-ray! 31% increase in power vs AixiZ acrylic!

* FS: New! 1000 Lumen XML-2 Maglite Modification With Voltage Monitor! - Parts or Complete Light! Must see!

* FS: Polished Stainless Steel Green Kit! Easy assembly in minutes!

* FS: Large Maglite Monster Kits! Side Button Forward Clicky! Custom Head Option! Gnarly...


Click here for a list of my build kits! Projects and tutorials too!

jayrob is offline   Reply With Quote
Reply





Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

























Privacy Policy | Advertising Disclaimer | Terms of Use


 


All times are GMT. The time now is 06:11 AM.


Powered by: vBulletin
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO
Privacy Policy | Advertising Disclaimer | Terms of Use
Copyright (C) 2017 Laser Pointer Forums, LLC