This polished Stainless Steel Green kit is available as a 'DIY Green Kit' without the battery or laser module... (links to the green modules are shown below)

Note: Some of my latest supply of the polished host, have green GITD tail caps instead of the blue ones. So you may get a GITD tail cap, or a blue one. Depending on my supply. All have the polished finish...

It is a very easy assembly that can be done in less than 5 minutes...

The kit includes:
* Host
* Heatsink with set screw (you will need a 1.5mm Allen wrench for the module set screw)
* All extra flashlight parts

This host/kit, has a nice sized heatsink for good heatsinking to the module! Once you have this kit, it will last you a lifetime. VERY easy to swap out modules if ever needed or desired!

This host will also work for rhd's 'Mosquito Module'. Specify this when ordering. See below...







Will fit any standard 12mm green module...

All you will need is a module (very easy to solder a small wire to bypass the switch - see picture below), a battery, and a 1.5mm Allen wrench for the set screw.

* The Kit will be $59 dollars plus shipping
* Shipping - $6
* Please read my shipping policy here!

The tolerance for the heatsink length is very close for a green build in this host. Because the heatsink needs to be held tight into the host with the head screwed onto the barrel. And if it is a little too long, there will be a noticeable gap between the head and the barrel. (see pictures of assembly)

Once it is screwed into place, you can remove/charge the battery by unscrewing the tail cap. So there is not any chance of the heatsink/module coming out when changing/charging batteries...




The O-like green modules are here for the specs on them:
50mW: Green laser module 50mW For custom build or lab [OLGLM50] - $26.99 : Welcome to O-Like.com, Your source for laser products
100mW: 100mW industrial green laser module [OLGLM100] - $58.99 : Welcome to O-Like.com, Your source for laser products
150mW: Green laser module 150mW For custom build or lab [OLGLM150] - $96.99 : Welcome to O-Like.com, Your source for laser products




Note: This host can also be used for a diode build. (red, blu-ray, 445)

It is the exact same host as my Stainless Steel 18650 kit shown here:
FS: Stainless Steel 18650 Kit! Polished! Perfect for 445...

Except with a green build, you will be using a CR123 (or RCR123) with the positive end of the battery towards the tail switch. (case positive)




This is a great 'Kit' for a DIY green build... You can use these pictures and first post, as a tutorial for the build...



Note: If you have a 4 pin style switch, it is easy to by-pass by connecting two of the points along either side. There are 4 solder points. Two at the the bottom (closest to the spring) And two at the top of the switch. (towards the aperture of the laser)

You can by-pass that style switch by soldering a small wire from one of the bottom points, to one of the top points. (easy to do)





If desired, you can easily make a sleeve for the battery (to make sure it cannot rattle) by cutting a sheet of plastic from a 2 liter soda bottle and rolling it up. Once you get the length needed, it will kind of 'self adjust' to fit inside the barrel...

This combination of a good size heatsink for your green module, and a very nice polished stainless steel host is a winner in my book...

Hope you like it!






Fitting for rhd's 'Mosquito Module'...

This host is a nice fit for rhd's Mosquito Module...

It means just customizing the heatsink to be bored larger at the back end. (for the driver to fit) The front of the heatsink will be fit for the AixiZ module, with a set screw.

With this particular kit, you will not be using the pill with a Mosquito module, so you need to order his module 'with spring'. (extra parts from the flashlight will be included)

My custom heatsink will be sized to be held in place when the head is screwed onto the barrel. You will just need to do some very easy adjusting of the module spring length. (or tail cap spring length as well)

With the Mosquito Module build, you will use 2 X RCR123 batteries instead of an 18650. Battery position - Case negative. (negative end of batteries towards tail switch)

* Stainless Steel Mosquito module kit (aluminum heatsink) - $59 (Mosquito module not included)

Very nice! I kinda wondered when you would do this haha. A+++!

Thanks...

Yeah I've just been busy with kit orders lately. But I have to make something new once in a while. It refreshes me!

Nothing wrong with a little "me" time! (especially now that I got my kit! Haha). Glad to see you having some fun building for yourself tho! Keep it up.

I just asked about this earlier today via PM

Bingo! I'll be getting one of these! Not now but soon!
Great work jay!

I want one as well, but I needs money to purchase one first...

I love this host, it is perfect for so many different builds (and it is a great flashlight to!!!)...Great job yet again jay!!!

If anyone has a pill I can buy of you I would greatly appreciate it. Just let Jay know if you want.

Is it ok to use a Li-Ion 3.6v battery in this? Or do I have to use a primary?

Well considering the battery in the picture is 3.6v

Nah it will be fine

Lots of people use the Li-Ion battery. Especially if it's a 100mW module or higher power...

But that said, I always test power with a 3 volt battery first. Because once in a while you get a really efficient module that will give very good power even with a 3 volt battery.

And if that is the case, it will last longer with the 3 volt supply.

The cheap that come with these modules, don't seem to be the kind of quality that we are used to with FlexDrives. If they were, the module would get the same current with either battery. But they generally give more power with a Li-Ion...

Minamoto Kobayashi, I sent your Stainless Steel Green kit with other kits and items today. (Tuesday)

Thanks for your patience...

Hope you like the kits!

imjustintime, I sent your Stainless Steel Green kits today. (Wednesday)

Hope you like them!

Yes its real. The tolerance for the heatsink length is very close for a green build in this host. Because the heatsink needs to be held tight into the host with the head screwed onto the barrel.

Yes correct, it's best if I have the host when fitting the heatsink...



a.martinez, I sent your Stainless Steel Green kit today. (Thursday)

Thanks!

Has anyone purchased from o-like? There website seems kind of empty in some of the navigation panels.

O-like is known for pre-tested modules and other good deals...


djoassoc, I sent your Stainless Steel Green kit today. (Friday)

Thanks!

Thanks jayrob it looks great. I ordered my batteries and module recently and cant wait to give it a shot. Looks like a great product.

Let me know how it goes!



falkon696969, I sent your Stainless Steel Green kit today. (Monday)

Hope you like it!

Hey guys! Well today I just got my 50mw module in the mail. I fitted my old 5mw module into the stainless kit and it worked great. There were only 2 available connections to choose from to which to solder, so that was a no brainer.

The 50mw module has 4 connections. I tried the 2 closest to the spring and the two farthest. Before I go jumping into solder a little bit more (currently outta time too) maybe you guys might be able to help. Here is a picture. Thanks!



the bottom if it helps

Easy to check continuity with your DMM by putting it on the setting that will 'beep' when the two probes are touched together...

Then just touch one probe to one solder point, and the other probe to a different solder point while testing the button.

But it will probably be the two on one side of the switch. Either side will probably not matter...

My grade: Outstanding. Not only did you put out a very nice product jayrob, the product your recommended was great as well. I chose to order the 50mw green module from o-like. Reasons for this was it was my first build, I didnt need to do any over kill. Also, being my first order from o-like I am now happy with their services as well.

Hopefully soon I can get some pictures up to compare from my old 5mw green laser pen on 2xAAA to the new 50mw on 1xCR123.

Actually the beam when projected on a wall 10' away is a little harsh to look at, probably could use some protective glasses when using the device. I see solid beams during the day about as bright as the 5mw laser could project at night.

When aiming into the sky at night, the intensity is incredible. The beam is solid all the way to the clouds. Looking forward to future builds. One day I will probably seek a high intensity flashlight when I complete my firefighting training and become a firefighter.

Thanks for posting back...

About a nice flashlight. I'm getting great feedback on my XM-L T6 Maglite mod over at Candle Power Forums. Please share the link with your fire house boys. I'm sure some of them will want one of these bad boys:
FS: 1000 Lumen XM-L T6 Maglite Modification Kit - Parts, or Complete Flashlight!

Jay: I couldn't be happier with my Stainless Green Kit. Fantastic. Only thing better than the kit is your impeccable service and support. All best, Harry

Thank you!

Very glad you like the kit!